Electrolux ESL 6180, Instruction Book

Page: 15 / 20

If after all these checks, the problem persists, contact your
local Authorised Service Centre, quoting the model (Mod.), the
PNC number and the serial number (S.N.).
This information can be found on the rating plate located on
the right hand side of the dishwasher door (see picture).
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod.: . . . . . . . . . . . . . . . . .
PNC: . . . . . . . . . . . . . . . . .
S.N.: . . . . . . . . . . . . . . . . .
Service and spare
parts
This product should be serviced by an authorised Service
engineer, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair the
machine yourself.
Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local
Authorised Service Centre.
Always insist on genuine spare parts.
Protection against flooding
In order to prevent water floods, the machine has been
provided with two devices, having the following characteristics:
1. In the water inlet hose (see "Water supply connections").
The device comes into operation as a result of any damage
to the water inlet hose and stops the water inflow.
To repair the machine call the Authorised Service Centre.
2. In the bottom of the machine:
The device comes into operation as a result of any water
leaks in the machine.
In case of intervention in the digital display will appear AL4.
To repair the dishwasher, turn off the water tap and call the
Authorised Service Centre.
15
RA08
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or competent
person.
Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a
drain.
Attention!
Carefully follow the instructions on the enclosed template for
building in the dishwasher and fitting the furniture panel.
Water supply connections
This dishwasher may be fed with either hot (max. 50°) or cold
water. Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled
crockery as it shortens the washing programmes a lot.
The water pressure must be within the limits given in the
technical specifications.
Your local Water Authority will advise you on the average
mains pressure in your area.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation. The
locknut must be correctly fitted to avoid water leaks.
Avoid bends or kinks in the hose which could prevent or slow
down the water supply.
If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose. This will prevent
deposits of sand or rust clogging the inlet hose filter.
For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto either a 3/4
inch gas thread spout, or to a purpose made quick-coupling
tap such as the Press-block.
Do not use, for connection, old hoses which have been
used in another appliance.
The water supply hose is fitted with a safety device, which
prevents water from entering the machine should the inner
hose split, due to wear.
The problem is signalled by a red indicator which appears in
the window (B -
➀ ➁
).
The retaining ring (A -
➀ ➁
) must be properly fitted so as to
avoid water leaks.
Note:
Only for water supply hoses fitted with Lock-fast safety device
to prevent inadvertent loosening.
To detach the hose press yellow lever (C -
➁
) and turn the
retaining ring anticlockwise
➁
.
Installation instructions
B
A
B
A
C
CA13
1
2