background image

14

Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.

Any plumbing work required to install this appliance
should be carried out by a qualified plumber or competent
person.

Remove all packaging before positioning the machine.

If possible, position the machine next to a water tap and a
drain.

Attention!
Carefully follow the instructions on the enclosed template for
building in the dishwasher and fitting the furniture panel.

Water supply connections 

This dishwasher may be fed with either hot (max. 50°) or cold
water.
Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled
crockery as it shortens the washing programmes a lot.

The water pressure must be within the limits given in the
technical specifications. 

Your local Water Authority will advise you on the average
mains pressure in your area. 

The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation.
The locknut must be correctly fitted to avoid water leaks. 

Do not use, for connection, old hoses which have been
used in another appliance.

Avoid bends or kinks in the hose which could prevent or slow
down the water supply. 

If the machine is connected to new pipes or pipes which have
not been used for a long time, you should run the water for a
few minutes before connecting the inlet hose. This will prevent
deposits of sand or rust clogging the inlet hose filter. 

For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto either a 3/4
inch gas thread spout, or to a purpose made quick-coupling
tap such as the Press-block.

Be sure to incorporate the
filter (A), supplied with the
machine, onto the joint.

Water outlet hose connection

The end of the drain hose can be connected in the following
ways: 

1. To the sink outlet spigot, securing it if necessary with a clip. 

2. To a stand pipe provided with vent-hole, minimum internal 

diameter 4 cm. 

The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher. 

The drain hose can face either to the right or left of the
dishwasher 

Ensure the hose is not bent or squashed as this could prevent
or slow down the discharge of water. 

The sink plug must not be in place when the machine is
draining as this could cause the water to siphon back into the
machine. 

If you use a drain hose extension it must be no longer than 2
metres and its internal diameter must be no smaller than the
diameter of the hose provided. 

Likewise the internal diameter of the couplings used for
connections to the waste outlet must be no smaller than the
diameter of the hose provided. 

Attention!
Our appliances are supplied with a security device to protect
against the return of dirty water back into the machine. 
If the spigot of your sink has a "no return valve" incorporated
this can prevent the correct draining of your dishwasher. 
We advise you therefore to remove it.

Installation instructions

CS13

min 30 cm

max 100 cm

min 4 cm

Ø 21

Ø 18

1

2

CS14

min 30 cm

max 100 cm

+ 2 m max

Ø 18

Ø 21

A

CA03

Summary of Contents for ESI 4120

















Reviews: