11
PR33
C
A
Inserire a scatto il coperchietto (C) sulla guida (A)
PR167/1
D
B
Inserire a scatto il coperchietto (D) sulla guida (B)
Aprire la porta dellÕapparecchiatura e quella del
mobile a 90¡ ca. Inserire la squadretta (B) nella
guida (A). Tenere insieme la porta dellÕapparecchia-
tura e quella del mobile e segnare i fori come
indicato in figura.
Togliere le squadrette e fare dei fori di ¯ 2 mm a 8
mm dal bordo esterno della porta. Posizionare
nuovamente la squadretta sopra le guida e fissare
con le viti in dotazione.
8mm
PR167
A
B
PR168
Per lÕeventuale operazione di allineamento della
porta del mobile, utilizzare il gioco dei fori asolati.
Al termine delle operazioni • necessario controllare
lÕesatta chiusura della porta dellÕapparecchiatura.
14
CONTENTS
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Use -
Cleaning the interior - Operation - Temperature regulation - Fresh food refrigeration . . . . . . . . . . . . .15
Use -
Movable shelves - Positioning the door shelves -
Hints -
Hints for refrigeration . . . . . . . . . . . . . . . . .16
Maintenance -
Periods of no operation
-
Periodic cleaning - Interior light - Defrosting . . . . . . . . . . . . . . .17
Customer service and spare parts
-
Technical information - Installation -
Location - . . . . . . . . . . . . . .
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Door reversibility - Building-in instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Installation
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear of
obstruction.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important:
if the supply cord is damaged, it must
be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
¥ If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to
wait at least two hours before connecting the
appliance to allow the oil to flow back in the
compressor.
¥ There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥ Parts which heat up should not be exposed.
Wherever possible the back of the product
should be against a wall.
¥ If the appliance has been transported
horizontally, it is possible that the oil contained in
the compressor ’lows in the refrigerant circuit. It
is advisable to wait at least two hours before
connecting the appliance to allow tlõe oil to flow
back in the compressor.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recyclable.