manualshive.com logo in svg

Electrolux EMS2685, Service Manual

Share
Download
Electrolux EMS2685 Service Manual Download Page 28

SOI  03.06  FV 

28/38 

599 36 78-45 

 

 

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

 

 

WARNING:   Avoid possible exposure to microwave energy. Please follow the instructions below 
 

before operating the oven. 

 

1. CARRY OUT 3D CHECKS. 
2. Make sure that a definite "click" can be heard 
  when the microwave oven door is unlatched. 
  (Hold the door in a closed position, then 
  push  the door open button slowly. This 
  causes the latch heads to rise, it is then 
  possible to hear a "click" as the door 
 switches 

operate.) 

3. Visually check the door and cavity face plate 
  for damage (dents, cracks, signs of arcing 
 etc.). 
 
Carry out any remedial work that is necessary 
before operating the oven. 
Do not operate the oven if any of the following 
conditions exist; 
1. Door does not close firmly.

 

 
2. Door hinges or latch hook is damaged. 
3. The door seal is damaged. 
4. The door is bent or warped. 
5. There are defective parts in the door interlock   system. 
6. There are defective parts in the microwave 
  generating and transmission assembly. 
7. There is visible damage to the oven. 
 
Do not operate the oven: 
1. Without the RF gasket (Magnetron). 
2. If the wave guide or oven cavity are not intact. 
3. If the door is not closed. 
4. If the outer case (cabinet) is not fitted.

 

 
Please refer to ‘OVEN PARTS, CABINET PARTS, DOOR PARTS’, when carrying out any of the following 
removal procedures: 

 

BUILT IN FRAME ASSEMBLY REMOVAL

 

 

To remove the built in frame assembly, proceed 
as follows. 
1.   Remove the four screws securing the frame 
 

assembly to the oven cavity, (two from the 

 

top and two from the hinge side). 

2.   Remove the two screws securing the frame 
 

assembly to the control panel frame 

 

(accessed from the back of the frame). 

3.   Open the oven door fully. 
4.  

Un-clip the built in frame assembly at the 

 bottom.

 

 
 

5.  Pull the built in frame assembly away from the cavity 
 face 

 

6.  Now the built in frame assembly is free.

 

 

OUTER CASE REMOVAL 

 

6. Slide the entire case back about 3cm to free it from 
  the retailing clips on the cavity face plate. 
7. Lift the entire case from the oven. 
8. Discharge the H.V capacitor before carrying any  further 
 work. 
9. Do not operate the oven with the outer case 
 removed.

 

 

To remove the outer case, proceed as follows. 
1.   Disconnect oven from power supply. 
2.   Open door and wedge open. 
3.   Remove the two screws from the rear 
 intake 

duct. 

4.   Slide the rear intake duct up and pull it 
 

away from the oven cavity. 

5.   Remove the screws from the rear(4), along 
 

the side edges(4 hinge side, 3 control panel 

 

side) and from the top(2 control panel side).

 

 

CAUTION: DISCHARGE HIGH VOLTAGE 
 

CAPACITOR BEFORE TOUCHING ANY 

 OVEN 

COMPONENTS 

OR 

WIRING. 

 

 

 

TOP 
SCREWS

 

C.P. SECURING
        SCREWS

 

HINGE SIDE
      SCREWS

 

Summary of Contents for EMS2685







































Reviews:

No comments

Brands by name

Popular brands

Load more brands