manualshive.com logo in svg

Electrolux EM1760X, Service Manual

Share
Download
Electrolux EM1760X Service Manual Download Page 3

SOI  01.05  FV 

3/33 

599 36 78-06 

 

TABLE OF CONTENTS 

 

 

 
 
CAUTION, MICROWAVE RADIATION / GENERAL INFORMATION .............................................4 
 
SERVICING......................................................................................................................................3 
 
PRODUCT SPECIFICATIONS.........................................................................................................6 
 
APPEARANCE VIEW.......................................................................................................................7 
 
OPERATING SEQUENCE .............................................................................................................10 
 
FUNCTION OF IMPORTANT COMPONENTS..............................................................................12 
 
TROUBLESHOOTING CHART......................................................................................................13 
 
TEST PROCEDURE ......................................................................................................................14 
 
CONTROL PANEL ASSEMBLY.....................................................................................................22 
 
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE..........................................24 
 
MICROWAVE MEASUREMENT....................................................................................................30 
 
TEST DATA A GLANCE / WIRING / RE-WIRING .........................................................................31 
 
SCHEMATIC DIAGRAMS ..............................................................................................................32 
 
PICTORIAL DIAGRAM...................................................................................................................33 

 
 
 

Summary of Contents for EM1760X


































Reviews:

No comments

Brands by name

Popular brands

Load more brands