27
Before cleaning the appliance,
turn off the mains
gas tap and
unplug the appliance or disconnect power at the main circuit
breaker of the electrical system.
Do not
clean appliance
surfaces when still hot.
Do not use steam cleaners to clean the oven.
IMPORTANT
Periodically check the external gas connection hole and replace
it when it shows any sign of
wear
. Do not
under any
cincumstances
attempt to repair the gas hose.
ENAMELLED SURFACES
Clean with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific cleansing
agent for enamelled surfaces. Do not use abrasive cleansers.
Do not leave any acid or alkaline substances (lemon juice, vinegar,
salt, etc.) on the enamel.
Clean the parts in stainless steel with specific cleansers for stainless
steel surfaces.
These detergents must be applied using a soft cloth.
GRIDS AND BURNERS
To clean the
cooktop
burners,
remove by
pulling upwards and soak
them for
approximately
10 minutes in hot water with a little detergent.
After
cleaning
and
washing
them,
dry
them carefully.
Make sure that burner holes
are not
clogged.
Clean the burners once a week or more frequently if necessary.
MAKE SURE YOU HAVE ASSEMBLED THE BURNERS
CORRECTLY
.
OVEN
Clean
enamelled
parts with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific cleansing
agent for enamelled surfaces.
Do not use abrasive cleansers.
Setting
To set, press and release the desired function, and within 5 seconds
set the time
using the
+ and - buttons.
+ and - buttons.
The + and - buttons increase
and
decrease the time
respectively
the
speed depending on how long the button is pressed.
Setting the time
Press any two buttons (cooking time, end time, minute
minder
) at the
same time, and + or - button to set the desired time. This deletes any
previously set programme. The contacts are switched off and the
AUTO symbol flashes.
Manual use
When
the manual button
is pressed
the relay contacts switch on, the
AUTO symbol switches off and the saucepan symbol lights up.
Manual operation can only be enabled after the automatic programme
is over it has been cancelled.
Automatic
function
Press the cooking time or end time button to switch automatically
from the manual to the automatic function.
A
U
T
O
Minute
minder
Cooking time
Cooking end
Manual
Decrease
time
Increase
time
GB
Display
4-
digit
, 7-
section
di
s
play for cooking times and
clock
.
Cooking time and manual function
=
saucepan symbol
Automatic function
=
AUTO
Minutes
minder
=
bell symbol
The symbols light up when the corresponding functions are selected.
“LED” PROGRAMMER (Fig. 4)
Features
24 hours clock with automatic
timer
and minute
minder
.
Functions
Cooking time, cooking end time, manual position, clock,
minute
minder
,
maximum programmable
time
23 hours 59 minutes.
Acoustic
signal
The
acoustic signal sounds
at the end of a programme or of the
minutes
minder
function and it lasts for a
maximum of
15 minutes.
To stop it, push any one of the functions buttons.
Start programme and check
The programme starts 4 seconds after it has been set.
The programme can be
verified
at any time by pressing the
corresponding button.
Setting error
A setting error is made if the time of day on the clock falls within the
cooking start and end times.
To correct the setting error, change the cooking time or cooking end
time.
The relays switch off when a setting error is made.
Cancelling a setting
To cancel a setting, press the cooking time button and then press the
- button until 00 00 appears on the display.
A set programme will automatically cancel on completion.
button
is pressed
the next cooking end time
is shown
on the display.
Set the cooking end time with + button. The relay and the cooking
time symbol switch off.
The symbol lights up again when the cooking start time
is reached
.
When the cooking time is
finished
, the AUTO symbol flashes, the
acoustic signal sounds and both
the cooking time symbol and the
relay switch off.
Minutes
minder
Press the minute minder button and set the cooking time with + or -
button.
The bell symbol lights up when the minutes
minder
is operating.
When the set time is
finished
, the
acoustic signal sounds
and the bell
symbol switches off.
Semi-automatic use
to set
cooking time
Press the cooking time button and set the desired time with + or -.
The AUTO and cooking time symbols light up continuously. The relay
switches on immediately. When the cooking end time
is reached
, the
relay and cooking time symbol switch off, the
acoustic signal sounds
and the AUTO symbol flashes.
Semi-automatic use
to set
end time
Press the end time button. The time of day appears on the display.
Set the cooking end time with + button. The AUTO and cooking time
symbols light up continuously. The relay contacts switch on. When
the cooking end time
is reached
, the relay and the cooking time symbol
switch off. When the cooking time is
finished
, the AUTO symbol
flashes, the
acoustic signal sounds
and both the relay and the cooking
time button switch off.
Fig. 4
Automatic use
to set
cooking time and end time
Press the cooking time button and select the
duration
of the cooking
time with + or - button. The AUTO and cooking time symbols light up
continuously. The relay switches on.
When
the
cooking end time
INSTRUCTIONS FOR
USING
THE
CONTROL DEVICE
CARE AND MAINTENANCE
