4-8
C
Co
om
mp
po
on
ne
en
ntt T
Te
ea
arrd
do
ow
wn
n
L
Lo
ow
we
err S
Sp
prra
ay
y A
Arrm
m
The lower spray arm is removed by grabbing the
spray arm in the center and pulling straight up.
G
Glla
as
ss
s T
Trra
ap
p R
Re
em
mo
ov
va
all
The glass trap is removed from the sump by
grabbing the handle and pulling up and out of the
sump.
P
Prre
es
ss
su
urriiz
ze
ed
d F
Fiin
ne
e F
Fiilltte
err A
As
ss
se
em
mb
blly
y
Water enters the pressurized fine filter assembly
from a port recessed into the right end of the
volute cover. Water exits through the fine mesh
screens down both sides of the filter leaving
trapped food particles and grit inside the
assembly.
The mesh screens on the sides of the filter are
cleaned by lower spray arm. The left end of the
filter is recessed into the pump out section of the
sump so trapped food particals and grit can be
easily pulled from the filter.
To remove the pressurized fine filter:
1.
Remove lower spay arm.
2.
Using a #20 Torx bit, extract the two screws
securing the pressurized fine filter to the
spray arm support. Lift pressurized fine filter
from stainless steel filter. (See Figure 5-16)
C
Ce
en
ntte
err S
Sp
prra
ay
y A
Arrm
m R
Re
em
mo
ov
va
all
The center spray arm mounts with a bracket to the
upper wire rack. The spray arm assembly passes
through the manifold mounting clip and slips into
the delivery tube manifold when the upper rack is
pushed into the tub. The spray arm is secured to
the spray arm assembly with a screw.
To remove the center spray arm:
1.
Remove the upper wire rack.
2.
Using a #10 Torx bit, extract the screw
securing the center spray arm to the spray arm
assembly. (See Figure 5-17)
3.
The spray arm assembly is separated from the
wire rack by lifting up on the retaining latch on
the mounting bracket and pushing the spray
arm assembly towards the back of the unit
until free of the mounting bracket, then pull
assembly out of the manifold mounting clip.
F
Fiig
gu
urre
e 5
5--1
16
6.. C
Co
on
nd
de
en
ns
se
err R
Re
em
mo
ov
va
all
Screw
Spray Arm
Support
Fine Mesh
Filter
F
Fiig
gu
urre
e 5
5--1
17
7.. S
Stta
aiin
nlle
es
ss
s S
Stte
ee
ell F
Fiilltte
err R
Re
em
mo
ov
va
all
Mounting Bracket
Retaining Clip
Manifold Mounting
Clip
Screw
Summary of Contents for EIDW6105GS0
