Built-In Microwave
EI30MO45G S
High standards of quality at Electrolux Major Appliances mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxappliances.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxappliances.ca
EI30MO45G 01/08
© 2008 Electrolux Major Appliances, NA
Printed in the U.S.A.
30" Built-In Microwave Specifications
•
Microwave Product Weight – 48 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 or 20 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.5 kW (For use on
adequately wired 120V, dedicated circuit having 2-wire service with a
separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 13 Amps
•
Always consult local and /or national electric codes.
•
Allow 21" minimum clearance for 90° door swing.
•
Built-in installation requires use of 30" Trim Kit (EI30MO45TK) which is
supplied and includes Stainless Steel Faceplate and Bottom Duct
Assembly – shipped in separate box.
•
Minimum 20" deep oven cutout dimension is critical for proper installation
for oven and faceplate to fit flush against cabinet front.
•
Consult local building code, in the event that cutout opening may be
required to be enclosed with sides, ceiling and rear partition.
•
Full base of solid plywood or similar material required, capable
of supporting 100 Lbs.
•
Base must be level and front of cabinet square for proper operation.
•
Grounded outlet should NOT be located in shaded area, as indicated.
•
Can NOT be installed above any gas wall oven.
•
Built-In Convection Microwave can be built in alone or is approved to be
used in combination with any Electrolux Electric Single Wall Oven and / or
Warmer Drawer.
•
When used in combination with another Electrolux built-in product, a
minimum clearance of 2-7/8" required from bottom of Built-In Microwave
cutout to top edge of companion product’s faceplate, leaving a 2" visible
gap between both product faceplates.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxusa.com for detailed instructions.
*
Note:
When used in combination with
another Electrolux built-in product, a
minimum clearance of 2
7
/
8
" required from
bottom of Built-In Microwave cutout to top
edge of companion product’s faceplate,
leaving a 2" visible gap between both
product faceplates
120V / 60Hz
grounded outlet
20" min.
4"
6"
4"
25
1
/
4
" min.
25
3
/
8
" max.
16
1
/
4
"
min.
16
3
/
8
"
max.
Bottom Duct Assembly
Outlet should
NOT be located
within shaded
area
30"
Allow at least
21" clearance for door
depth when open
18
1
/
16
"
24
"
15
3
/
4
"
Power
cord
location
(right
top rear)
Faceplate
13
3
/
8
"
2
5
/
16
"
30" min.
20"
min.
7
/
8
"
Faceplate
overlap
16
1
/
4
"
min.
16
3
/
8
"
max.
Full
plywood
base
required
to support
100 lbs.
25
1
/
4
" min.
25
3
/
8
" max.
2" (visible
gap)*