background image

 

 

 

 

EN 

 

9

 

USE

 

L T1 T2 T3 T4 T5 F

 

 

 

 

The hood can be switched on pushing directly onto the requested speed without firstly hav-
ing to select 0/1 button .

 

Basic functions 

Touch 
control

 

Dual Function 

Indicator lights 

When briefly pressed it switches the lighting system 
on and off. 

Touch control unlit   Lights off 

Touch control lit   

Lights on 

When pressed for 2 seconds it starts the lighting 
system in “courtesy light” mode. The lamps are 
fed at a reduced power of approximately 5W. 
Such function can be stopped by pressing the 
touch control for 2 seconds or just by pressing it 
shortly in order to return to the normal lighting 
mode. In courtesy light mode the touch control is 
not lit. 

Touch control unlit    Courtesy light on 

Touch control lit  

Motor on 

T1 

When pressed the motor is stopped, regardless of the 
speed it is set to.

 

Touch control unlit   Motor off 

T2 

When pressed the motor is set to the first speed

 

Touch control lit   

By a brief pressing the motor is set to the second 
speed. 

Touch control lit   

Second speed on 

T3 

By pressing the touch control for approximately 2 
seconds the Delay function is enabled, i.e dela-
yed shutdown of the appliance ensuring a com-
plete elimination of the residual odours. This fun-
ction can be activated at OFF-position and at 1°, 
2° and 3°speeds. It can be stopped in advance 
by pressing any of the touch controls (T) with the 
exception of T3. The Delay function works accor-
ding to the following scheme: 

1°speed / OFF 

=  20 minuets 

2°speed  

15 

minutes 

3°speed = 

minutes 

Flashing touch 
control  

Delay function on 

T4 

When pressed the motor is set to the third speed

 

Touch control lit      

Summary of Contents for EFC 9543

















Reviews: