Electrolux EAW05E3AJW Instruction Manual Download Page 18

Security

33 electrolux 

security

security

 electrolux 34

Incorrect operation due to ignoring of 
instructions may cause harm or 
damage. The seriousness is classified 
by the following indications:

Plug in power plug properly: 

Otherwise, it may cause electric 
shock or fire due to excess heat 
generation.

Do not operate or stop the unit by 
inserting or pulling out the power 
plug: 

It may cause electric shock or 

fire due to heat generation.

Do not damage or use an unspecified 
power cord: 

 It may cause electric 

shock or fire. If the power cord is 
damaged, it must be replaced by the 
manufacturer or an authorised service 
centre or a similarly qualified person in 
order to avoid a hazard.

Do not modify power cord length or 
share the outlet with other 
appliances: 

It may cause electric 

shock or fire due to heat generation.

Do not operate with wet hands or in 
damp environment: 

It may cause 

electric shock.

Do not direct airflow at room 
occupants only: 

This could damage 

your health.

Always ensure effective earthing: 

Incorrect earthing may cause electric 
shock.

Do not allow water to run into 
electric parts: 

It may cause failure of 

machine or electric shock.

Always install circuit breaker and a 
dedicated power circuit: 

Incorrect 

installation may cause fire and electric 
shock.

Unplug the unit if strange sounds, 
smell, or smoke comes from it: 

It 

may cause fire and electric shock.

Do not use the socket if it is loose 
or damaged: 

It may cause fire and 

electric shock.

Do not open the unit during 
operation: 

It may cause electric 

shock.

Keep firearms away: 

It may cause 

fire.

Do not use the power cord close to 
heating appliances: 

It may cause fire 

and electric shock.

Do not use the power cord near 
flammable gas or combustibles, 
such as gasoline, benzene, thinner, 
etc.: 

It may cause an explosion or fire.

Ventilate room before operating air 
conditioner if there is a gas leakage 
from another appliance: 

It may 

cause explosion, fire and, burns.

Do not disassemble or modify unit: 

It may cause failure and electric 
shock.

Do not drink water drained from air 
conditioner: 

It contains contaminants 

and could make you sick.

When the air filter is to be removed, 
do not touch the metal parts of the 
unit: 

It may cause an injury.

Do not clean the air conditioner 
with water: 

Water may enter the unit 

and degrade the insulation. It may 
cause an electric shock.

Ventilate the room well when used 
together with a stove, etc.: 

An 

oxygen shortage may occur.

When the unit is to be cleaned, 
switch off, and turn off the circuit 
breaker: 

Do not clean unit when 

power is on as it may cause fire and 
electric shock, it may cause an injury.

Do not put a pet or house plant 
where it will be exposed to direct 
air flow: 

This could injure the pet or 

plant.

Use caution when unpacking and 
installing: 

Sharp edges could cause 

injury.

Stop operation and close the 
window in storm or hurricane: 

Operation with windows opened may 
cause wetting of indoor and soaking 
of household furniture.

Do not place obstacles around air-
inlets or inside of air-outlet: 

It may 

cause failure of appliance or accident.

Hold the plug by the head of the 
power plug when taking it out: 

It 

may cause electric shock and 
damage.

Always insert the filters securely. 
Clean filter once every two weeks: 

Operation without filters may cause 
failure.

Do not place heavy object on the 
power cord and ensure that the 
cord is not compressed: 

There is 

danger of fire or electric shock.

Do not use the following items: 

Warm water (more than 40°C or 
104°F). The warm water can deforme 
or  bleach the window air conditioner.

Never clean the appliances with 
flammable liquids as alcohol, 
kerosene, gasoline, some liquid 
cleaners, some spots removers,  
turpentine, waxes, wax removers, or 
cleaners as amoniac, acids, vinagers, 
soda or abrasives as plastic or steel 
sponges, steel wool, neither also with 
chemical products that migh release 
chemical  corrosive or toxic vapors 
that may damage the appliance.

Do not use for special purposes: 

Do 

not use this air conditioner to preserve 
precision devices, food, pets, plants, 
and art objects. It may cause 
deterioration of quality, etc. 

Turn off the main power switch 
when not using the unit for a long 
time: 

It may cause failure of product 

or fire.

Ensure that the installation bracket 
of the outdoor appliance is not 
damaged due to prolonged 
exposure: 

If bracket is damaged, 

there is concern of damage due to 
falling of unit.

E

N

G

E

N

G

Summary of Contents for EAW05E3AJW

































Reviews: