background image

- 3 -

IntroductIon

Thank you for choosing the Electrolux Wine Cellar. 
Please read the following instructions carefully be-

fore installing your new wine cellar. We trust you 

will be completely satisfied with your purchase. 

The wine cellar must be installed and used accord-

ing to these instructions in order for it to operate 

correctly and economically.

transIt damage

Inspect the wine cellar for transit damage. You 

must report any damage the company responsible 

for the delivery within the legal or stated time for 

this type of product. If there is no such established 

report time, the damage must be reported within 

seven days of delivery.

accessorIes

Please check that the following accessories are at-

tached to the Wine Cellar or in the separate card-

board box inside the wine cellar.
Cardboard box:

Handle
Storage shelves
Drip tray

Support (floor)

Shelf supports
Screws

Washers (wooden door)

Keys
CD
Instruction manual

Necessary additional tools not included:

Screwdriver (star quad)

Adjustable spanner or fixed spanner (21 mm)










data plate

Check the data plate, inside the wine cellar at  

the top left, to ensure you have received the right 

model.
The data plate shows details 

that you will need to quote if 

you have to contact service 

personnel.

It is a good idea to make a note of them here:

Model designation . . . . . . . . . . . . . . . . . . . . . . . .
Product number . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial number . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

InstallatIon

Please follow these instructions:

For best performance, air needs to circulate free-

ly over the cooling unit behind the wine cellar. 
The free-standing design of the cellar means that 

it should stand at least 25 mm from the rear and 

side walls. 
Allow a clearance of at least 100 mm above the 

wine cellar.  

 

 

 

 

 

 

 

 

 

 

Note that it must be possible to open the wine 

cellar door at least 90° to allow the sliding 

shelves to be pulled out. 

30 mm

25 mm

25 mm

Rear

Wall

Wall

Summary of Contents for Dometic CS 110













Reviews: