Electrolux 532140600 Owner'S Manual Download Page 11

11

TIPS FOR IMPROVED BAGGING 
OPE RA TION:

Follow the mower operation instructions in your tractor 
owner's manual.

When operating your grass catcher on a lawn where grass 
and leaf bagging equipment has not been used, you are 
picking up thatch and debris that has accumulated for long 
periods of time. The amount collected and the total time 
of operation may be greater than you will experience with 
regular use of your grass catcher.

•      Always run throttle at full speed when bagging.
•      Select a gear low enough to give good mower cutting 

performance, good quality cut and good bagging 
per for man ce.

NOTE

: It may be necessary to overlap width of cut to suit 

your conditions.
•      If grass is extremely tall, it should be mowed twice. The 

fi rst time relatively high, the second time to desired 
height.

•      Use left hand side of mower for trimming.
•        Plastic trash bags can be inserted inside grass catcher 

containers for ease of debris disposal. To remove the 
plastic trash bags when full:

a.  Disengage blades, shift into neutral, en ga ge the 

par king brake and stop the engine.

b.  Raise seat. Unlatch and raise cover.
c.  Remove one container at a time by grasping 

con tai ner handles and pulling toward the rear, off 
of the tube rails.

d.  With the container resting on the ground, close 

and secure the top of the plastic lawn bag.

e.  Tip the container on its side and slide the fi lled bag 

from the container.

f.  Install a new plastic lawn bag with the edges of the 

bag draped over upper lip of the container.

g. Repeat 

for 

other 

containers.

h.  Reinstall containers making sure  right con tai ner 

overlaps left container at center supports.

j. 

Close cover and secure latches over center support 
tubes.

•      Avoid cutting wet grass or in the morning while the dew 

is still heavy. Grass clippings collected under these 
conditions tend to be sticky and adhere to the walls of 
the fl ow path causing clogging.

•     Your bagger is equipped with a full bagger indicator. 

Movement of the wheel increases as the bags fi ll. The 
wheel will be spinning fastest just before the bags fi ll 
completely. When the wheel stops, it indicates that the 
bags are full and the chutes have become clogged. 

NOTE

: To help prevent clogging of chutes, check/empty 

bags when the wheel is spinning fast. Experience will teach 
you the best time to empty the bags.
       Care should be taken not to damage the parts and that 

the wheel spins freely at the beginning of each use.

•      If the grass catcher fails to pick up cut grass or leaves, 

it is an indication that clogging has occurred in the 
system or that the grass catcher containers are full. 
Usually this is indicated by the stopped movement of 
the full bagger indicator.

a.   Disengage blades, shift into neutral, en ga ge the 

par king brake and stop the engine.

-  Raise seat. Unlatch and raise cover. 

-  Slide out containers and dispose of clip pings . 

-  Replace containers, close cover, and latch.

b.  Unlatch chutes and check for clogging.

-  Remove all debris in chutes.

- Reassemble and latch chutes

c.    Check to insure full bagger indicator has not become 

clogged.

-  The air passage hole must be clear of debris. 

Gently insert a small twig or wire into pas sage way 
to clear.

CAUTION

 

•  Do not operate mower with grass catch er 

par tial ly installed.

 

•  Disengage blades and stop engine be fore 

leav ing tractor seat to empty con 

tain ers, 

un clog ging chutes, etc.

 

•  Close cover before starting.

 

•  Disengage mower when crossing drive ways 

or gravel surfaces and other areas where 
thrown objects could be a hazard.

 

•  Do not attempt to vacuum up cans or other 

potentially hazardous pro jec tiles.

OPERATION

Summary of Contents for 532140600


















Reviews: