Polyethylene
• Outer wrapping
• Instructions bag
Polypropylene
• Straps
Polystyrene foam
• Corner protectors
E
E..4
4
JJo
oiin
niin
ng
g A
Ap
pp
plliia
an
ncce
ess
1. Undo the 4 fixing screws and remove the control panels of
the appliances (Fig.1A);
2. Remove the fixing screw nearest the control panel, from
each side to be joined (Fig.1B);
3. Bring the appliances together and turn the feet to level
them until the tops match (Fig.1D);
4. Turn one of the two plates inside the appliances 180℃
(Fig.1C);
5. From inside the control panel of the same appliance, join
them at the front side, screwing one M5x40 Hex Head
screw (supplied) on the opposite insert (Fig.1E);
6. From the rear of the appliances, insert the coupling plate
(provided) in the side slots on the back panels;
7. Secure the plate with two flat head M5 screws provided
(Fig.1F).
E
E..4
4..1
1
F
Fllo
oo
orr F
Fiixxiin
ng
g ((d
de
ep
pe
en
nd
diin
ng
g o
on
n tth
he
e a
ap
pp
plliia
an
ncce
e a
an
nd
d//o
orr
m
mo
od
de
ell))
To avoid accidental tipping of built-in half-module appliances
installed separately, fix them to the floor carefully following the
instructions enclosed with the corresponding accessory
(F206136).
E
E..4
4..2
2
IIn
nsstta
alllla
attiio
on
n O
On
n B
Brriid
dg
ge
e,, C
Ca
an
nttiille
evve
err F
Frra
am
me
e O
Orr
C
Ce
em
me
en
ntt P
Plliin
ntth
h ((d
de
ep
pe
en
nd
diin
ng
g o
on
n tth
he
e a
ap
pp
plliia
an
ncce
e a
an
nd
d//
o
orr m
mo
od
de
ell))
Carefully follow the instructions enclosed with the correspond-
ing accessory. Follow the instructions supplied with the
optional product chosen.
E
E..4
4..3
3
S
Se
ea
alliin
ng
g G
Ga
ap
pss B
Be
ettw
we
ee
en
n A
Ap
pp
plliia
an
ncce
ess
Follow the instructions supplied with the optional sealing paste
pack.
E
E..5
5
G
Ga
ass,, e
elle
eccttrriicciittyy a
an
nd
d w
wa
atte
err cco
on
nn
ne
eccttiio
on
nss ((iiff
p
prre
esse
en
ntt,, d
de
ep
pe
en
nd
diin
ng
g o
on
n tth
he
e a
ap
pp
plliia
an
ncce
e a
an
nd
d//o
orr
m
mo
od
de
ell))
• Any installation work or maintenance to the supply system
(gas, electricity and/or water, if present) must only be
carried out by the utility company or an authorised
installation technician.
• Refer to the appliance dataplate for the product code.
• See the installation diagram for the type and position of
appliance connections.
E
E..6
6
G
Ga
ass C
Co
on
nn
ne
eccttiio
on
nss
E
E..6
6..1
1
IIn
nttrro
od
du
uccttiio
on
n
C
CA
AU
UT
TIIO
ON
N
This appliance is arranged and tested to
operate with G20 gas 20 mbar;
To convert it to another type of gas, follow the instructions in
E.6.6
Conversion to another type of gas paragraph of this
section.
E
E..6
6..2
2
F
Fu
um
me
e e
exxh
ha
au
usstt
• “A1“ type appliances have to be positioned under an
extraction hood to ensure removal of fumes and steam
produced by cooking;
(not relevant for Australian standard).
For A
AU
US
ST
TR
RA
AL
LIIA
A: the ventilation must be in accordance with
Australian building codes and kitchen exhaust hoods must
comply with AS/NZS1668.1 and AS 1668.2.
E
E..6
6..3
3
B
Be
effo
orre
e cco
on
nn
ne
eccttiin
ng
g
1. Make sure the appliance is arranged for the type of gas to
be used.
Otherwise, carefully follow the instructions given in E.6.6
Conversion to another type of gas paragraph of this section.
2. Fit a rapid gas shutoff tap/valve ahead of each appliance.
3. Install the tap/valve in an easily accessed place.
4. Clean the pipes to remove any dust, dirt or foreign matter
which could block the supply.
The gas supply line must ensure the gas flow necessary for
full operation of all the appliances connected to the system.
A supply line with insufficient flow will affect correct
operation of the appliances connected to it.
1A
180
1B
1C
N7E
N9E
1E
1F
1D
N7E N9E
18
