ELECTROCOMPANIET AW 120 Owner'S Manual Download Page 6

Service Policy:

When service is needed
Your dealer will have all relevant information about the service centres in your area,
and will ensure that your unit is serviced without delay. It is our general policy to
have your amplifier returned to you within 5 working days. This is an average time,
and could vary locally, depending on the work load at the service centre.
If, for some reason, there are no service facilities available in your country, please
ship the amplifier to the following address:

E

lectrocompaniet as

    Breivikveien 7

        

N-

4120 Tau

, N

orway

 

 

 

F

ax:

 +47 

51 74 10 10

www.electrocompaniet.no

E-mail : 

service

@electrocompaniet.no

You are responsible for all shipping charges, insurance, re-importation to your
country, and duty arrangements. When shipping a product to the factory for service,
always include the following:

1) A sales slip or other proof of purchase if repair is claimed under

warranty

2) A proforma invoice with value of the goods, stating that the

amplifier is returned to Norway for repair.

3) An accompanying letter describing faults, symptoms, or problems

with the amplifier.

4) Always ship the amplifier in its original carton and packaging

material to prevent damage in transit.

Electrocompaniet will not accept responsibility for any damage caused in transit, 
how ever caused.
If you require further information concerning the amplifier operation, or if you have
any questions related to service, please do not hesitate to contact your dealer or

your 

national Electrocompaniet distributor.

Summary of Contents for AW 120







Reviews: