background image

X

-Array Install™-1152/64 Loudspeaker System

8

X-Array Install™ Xi-1152/64 Loudspeaker System

Specifications

Frequency Response (measured in far
field, calculated to one meter on axis,
swept si ne wave, one watt into LF
section 2.83 V at 250 Hz, anechoic
environment; see Figure 2):

50-16,000 Hz

Crossover Frequency:

1,500 Hz

Efficiency, LF/HF:

4.2/25 %

Maximum Long-Term-Average Power-
Handling Capacity (per ANSI/EIA RS-
426-A 1980), LF/HF:

600/75 watts

Maximum Long-Term-Average
Midband Acoustic Output, LF/HF:

25/19 acoustic watts

Sensitivity (SPL at one meter, indicated
input power, anechoic environment,
average level), LF/HF,

1/1 watt:

98.0/113.0 dB

300/75 watts:

122.8/131.8 dB

Beamwidth (angle included by 6-dB-
down points on polar responses,
indicated one-third-octave bands of
pink noise; see Figures 1 and 3),

Horizontal, 1,200-16,000 Hz:

60° (+40°, –5°)

Vertical, 1,200-16,000 Hz:

40° (+28°, –15°)

Directivity Factor, R

θθθθθ

(Q), 1,200-16,000

Hz Average (see Figure 4):

21.9 (+8.0, –8.9)

Directivity Index, D

i

, 1,200-16,000 Hz

Average (see Figure 4):

13.4 dB (+1.3 dB, –2.3 dB)

Distortion (115 dB SPL at one meter,
shaped spectrum; see Figure 5),

Second Harmonic,

100 Hz:

2.5 %

500 Hz:

0.2 %

2,000 Hz:

1.4 %

5,000 Hz:

1.1 %

Third Harmonic,

100 Hz:

0.7 %

500 Hz:

0.3 %

2,000 Hz:

<0.1 %

5,000 Hz:

<0.1 %

Transducer Complement,

HF:

DH6 driver, HP64S 60° x 40° horn

LF:

EVX-155 15-in. woofer

Impedance (see Figure 6),

Nominal, LF/HF:

8/16 ohms

Minimum, LF/HF:

6.3/14.0 ohms

Input Connections:

Two Neutrik NL4MPR Speakon

®

connectors paralleled

Recommended Amplifier Power,

HF:

125-250 watts

LF:

600-1,200 watts

Enclosure Construction,

Enclosure Shell:

18-mm, 13-ply birch plywood

Finish:

Black textured paint

Grille:

Vinyl-coated steel with foam

Rigging:

Two-point heavy-duty L-track system,
accepts New Haven NH32102-2
double-stud fittings, or New Haven
NH8192-2S or Ancra 42546-10 single-
stud fittings with safety pins

Dimensions,

Height:

759 mm (29.88 in.)

Width (front):

450 mm (17.73 in.)

Width (back):

248 mm (9.75 in.)

Depth:

413 mm (16.28 in.)

Angle:

30° wedge

Net Weight:

40.8 kg (90 lb)

Shipping Weight:

43.1 kg (95 lb)

SPEAKERS - X-Array Install

Part Number 535192RevA — 9822

600 Cecil Street, Buchanan, MI 49107

800/234-6831, 616/695-6831, 616/695-1304 Fax

©Telex Communications, Inc. 1998 • Litho in U.S.A.

Summary of Contents for Xi 1152









Reviews: