EVI-15 F
ull-Range Loudspeaker
EVI-15 Full-Range Loudspeaker
Part Number 534764-EXP.— 9820
600 Cecil Street, Buchanan, MI 49107
616/695-6831, 616/695-1304 Fax
©Telex Communications, Inc., 1998 • Litho in U.S.A.
Specifications:
Versions Available:
EVI-15 black
EVI-15 white
System Type:
Direct-radiating vented-bass full-
range loudspeaker system
Pressure Sensitivity:
1
100 dB SPL
Frequency Response (see Figure 1):
2
50 Hz - 20 kHz
Power Handling:
3
250 watts, long-term continuous
1,000 watts, peak power
Maximum Output:
4
123 dB SPL, long-term continuous
128 dB SPL, peak power
Impedance (see Figure 2):
8.0 ohms nominal
5.9 ohms minimum (15.8 kHz)
Beamwidth,
Long Throw:
Horizontal, 1-20 kHz:
60° (+30°, -2°)
Vertical, 1-20 kHz:
70° (+30°-10°)
Short Throw:
Horizontal, 600 Hz-20 kHz:
110° (+25°, -25°)
Vertical, 600 Hz-20 kHz:
90° (+25°, -18°)
Directivity Factor, R
θθθθθ
(Q), 1.2-20 kHz:
14.0 (+5.5, -4.0)
Directivity Index, D
i
, 1.2-20 kHz
12.5 dB (+1.2 dB, -2.7 dB)
Components:
High-efficiency, high-power cast-
frame 381-mm (15-inch) woofer with
one 25.4-mm (1.0-inch) exit com-
pression driver mounted to a small-
format Vari Intense
®
horn
Input Terminals:
Large screw terminals
Replacement LF:
1815-0992
Replacement HF:
833-0990
Replacement Grille:
73574 black
73753 white
Enclosure:
Direct-radiating vented LF, built of
19-mm (0.75-inch), 7-ply birch
plywood with appropriate bracing,
lined with glass wool; five 3/8-16
shoulder bolt hanging points included
Dimensions:
584 mm (23.0 in.) high
429 mm (16.9 in.) wide
766 mm (30.2 in.) deep
Net Weight:
24.0 kg (53 lb)
Shipping Weight:
28.2 kg (62 lb)
Finish:
Black or white textured paint with
black or white 16-gauge powder-coated
grille
Accessories:
Electro-Voice MB-EVI15 U-Bracket
suspension kit
Electro-Voice EBK-1 Eyebolt suspen-
sion kit
Notes on Measurement Conditions
1. Band-limited pink noise signal, one watt
calculated using E
2
/Z
min
, 3.16-meter measure-
ment distance referred to one meter.
2. On-axis, one watt calculated using E
2
/Z
min
,
3.16-meter measurement distance referred to
one meter, low frequencies corrected for
anechoic-chamber error.
3. This system rating is patterned after the
ANSI/EIA RS-426-A method where the test
signal is pink noise with a 6-dB crest factor
over the bandwidth of the system, with
power calculated using E
2
/R
E
x 1.15, for 8
hours.
4. This measurement made under the same
conditions as pressure sensitivity, and takes
into account any power-compression effects
due to nonlinearities in the system.
5. The distortion at any given frequency
may be found by graphically taking the dif-
ference between the fundamental and har-
monic, and adding the number of decibels
which the harmonic has been raised on the
graph and apply the formula: percent dis-
tortion = 100 x 10
(-difference in dB/20)
6. The use of Vari Intense
®
horns is protected
by U.S. patent # 5,020,630.
6
