Electro Industries/GaugeTech Shark 200T Page 5 Quick Start Manual Download

Page: 5 / 8

Doc

E149704 V.1.08

QS - 5

Shark® 200T Quickstart

Electro

Industries/GaugeTech

™

Powered by Innovation™

Follow these steps to connect to the meter via RS485:

1. Connect the meter to the PC, using an RS485 cable. EIG offers a RS485 to USB connector, which can

be ordered from EIG’s website:

https://www.electroind.com/product/rs485-to-usb-communication-

-converter/

2. Open CommunicatorPQA

software (see page QS-1 for the download link).

3. Click

Connect

in the Icon Bar.

4. You will see the Connect screen. Make sure

your settings match the ones shown on the right

(use pull-down menus).

5. Click

Connect

. The Device Status screen confirms

the connection. Click OK to close the Device Status

screen.

6. Click the

Profile

button on the Icon bar.

7. The Device Profile screen opens. The Tree menu on the left side of the screen lets you choose

setting screens. Click on a plus sign to view the settings

screen options.

Summary of Contents for Shark 200T









Search results

Summary of Contents for Shark 200T

Reviews:

Related manuals for Shark 200T

Brands by name

Popular brands

Electro Industries/GaugeTech Shark 200T, Quick Start Manual

Search results

Summary of Contents for Shark 200T

Reviews:

Related manuals for Shark 200T

Brands by name

Popular brands