manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 253 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 253

     

Doc

#    

E154713     

                              

             C-15

C: Using the IEC61850 Protocol Ethernet Network Server

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

C.1.4.2: GOOSE 

The GOOSE implementation enables the Nexus® 1500+ meter with the IEC 61850 
server to:

•  Send and receive (publish/subscribe) messages

•  Send messages when programmed limits have been exceeded

•  Receive messages of exceeded limits and trigger waveforms in response to them

•  Enabling GOOSE, configuring limits, and selecting the limits that will 

trigger waveform capture is done in the Device Profile. See Section C.1.4.1: IEC 
61850 Protocol Server on page C-12, for instructions. 

•  The programming of the GOOSE send and receive of messages is done in the CID 

file.

Refer to the figure below for an illustration of GOOSE functionality.

C.3: GOOSE Cross-Triggering of Waveforms

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments