ENTERING/EXITING BYPASS
Switch between
buffered
bypass
and effect mode by tipping the Slammi forward, in
the toe direction, past the flat position of the Slammi. You do not need to tip the
Slammi all the way forward; 25% of the total forward travel will do it. The Slammi
needs to return to its flat position before you can switch between bypass and effect
mode again.
When the Slammi is in effect mode, the EHX logo in the center of the pedal will light
up. In bypass mode, the logo does not light.
POWER
Plugging into the INPUT jack activates power from the internal 9 Volt battery. The
input cable should be removed when the unit is not in use to avoid running down the
battery. If an AC Adapter is used, the Slammi will be powered up as long as the AC
Adapter is correctly plugged in.
The Slammi’s power jack is located on the same side as the OUTPUT jack. A 9 Volt
AC Adapter capable of delivering at least 50 mA of current is required to power the
Slammi. The inner ring of the 9 Volt AC Adapter must be negative, the outer ring
positive. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI (same
as used by Boss
®
& Ibanez
®
) 9.6 Volts DC/200mA. The unit’s battery may be left in
or taken out when the AC Adapter is in use.
The actual current draw of the
Slammi is 24 mA.
CHANGING THE BATTERY
1.
Locate the battery door at the front of the Slammi, under the toe area of the
foot plate.
2.
Remove the large black screw that holds the battery door to the case, most
coins or larger slotted screwdrivers can be used to remove this screw.
3.
Connect your new 9V battery to the wired battery connector.
4.
Insert the 9V battery into the battery holder clip on the battery door so that
the wired connector is on the same side of the hole in the battery door.
5.
Place the battery door back into its window, in the case of the Slammi and
re-install the screw.
NOTES AND SPECIFICATIONS
Slammi has buffered bypass.
The input impedance presented at the INPUT Jack is 2M
. The output
impedance at the OUTPUT Jack is 780
.
The current draw of the Slammi
is 24 mA.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete and
return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will
repair or replace, at its discretion, a product that fails to operate due to defects in
materials or workmanship for a period of one year from date of purchase. This
applies only to original purchasers who have bought their product from an authorized
Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the
unexpired portion of the original warranty term. If you should need to return your
unit for service within the warranty period, please include a brief description of the
problem as well as you name, address, telephone number, copy of your receipt, and
a check or money order. The costs for shipping and handling are listed below.
United States - $12
Canada - $15
Europe and other countries - $25
Ship to:
Electro-Harmonix
C/O New Sensor Corporation
55-01 2nd Street
Long Island City, NY 11101
Attn:
Service Department
Please make checks/money orders payable to New Sensor Corporation.
To hear demos on all EH pedals visit us on the web at
www.ehx.com.
Email us at
- FCC COMPLIANCE -
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
.
Modifications not expressly approved by the manufacturer could void the user's authority to
operated the equipment under FCC rules.
