3
This output’s signal is line-level, and is controlled by the active Volume knob.
When the EHX TORTION is in bypass mode, the DI output and cabinet simulator
are still active, and send your bypass signal through the simulator. This can be
used to warm up the sound of other pedals or processors for recording.
9V Power Jack
– Although the EHX TORTION accepts 9V Batteries, it is
supplied from the factory with an Electro-Harmonix 9.6DC-200BI power supply.
Plug the output of the supplied AC Adapter into the 9V power jack located at the
top of the EHX TORTION. The EHX TORTION draws 27mA at 9VDC with a center
negative plug. The EHX TORTION accepts Boss
®
and Ibanez
®
style AC Adapters.
- CHANGING THE BATTERY -
To change the 9-volt battery, you must remove the 4 screws on the bottom of
the EHX TORTION. Once the screws are removed, you can take off the bottom
plate and change the battery. Please do not touch the circuit board while the
bottom plate is off or you risk damaging a component. Avoid touching the
trimmers on the circuit board. These have been set at the factory for proper
operation. Changing these trimmers can result in a non-functional unit.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete
and return the enclosed warranty card within 10 days of purchase. Electro-
Harmonix will repair or replace, at its discretion, a product that fails to operate
due to defects in materials or workmanship for a period of one year from date of
purchase. This applies only to original purchasers who have bought their product
from an authorized Electro-Harmonix retailer. Repaired or replaced units will then
be warranted for the unexpired portion of the original warranty term.
If you should need to return your unit for service within the warranty period,
please contact the appropriate office listed below. Customers outside the regions
listed below, please contact EHX Customer Service for information on warranty
repairs at [email protected] or +1-718-937-8300. USA and Canadian customers:
please obtain a
Return Authorization Number
(RA#) from EHX Customer
Service before returning your product. Include with your returned unit: a written
description of the problem as well as your name, address, telephone number, e-
mail address, and RA#; and a copy of your receipt clearly showing the purchase
date.
United States & Canada
EHX CUSTOMER SERVICE
ELECTRO-HARMONIX
c/o NEW SENSOR CORP.
55-01 2ND STREET
LONG ISLAND CITY, NY 11101
Tel: 718-937-8300
4
Email: [email protected]
Europe
JOHN WILLIAMS
ELECTRO-HARMONIX UK
13 CWMDONKIN TERRACE
SWANSEA SA2 0RQ
UNITED KINGDOM
Tel: +44 179 247 3258
Email: [email protected]
This warranty gives a purchaser specific legal rights. A purchaser may have even
greater rights depending upon the laws of the jurisdiction within which the
product was purchased.
To hear demos on all EHX pedals visit us on the web at
www.ehx.com
Email us at
- FCC COMPLIANCE -
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation. If the device is not installed and used in accordance with the instructions, it
may cause harmful interference to radio communications and void the user's authority to
guarantee the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help
.
Modifications not expressly approved by the manufacturer could void the user's authority to
operate the equipment under FCC rules.
