ElectrIQ EPMH1000LED User Manual Download Page 4

 

 

Always  ensure  the  unit  is  secure  before  operation.  Do  not  use  on  unstable  or 
uneven surfaces and if wall-mounted, it must be securely attached to a suitable 
wall.   

 

Do not move or tilt the unit. 

 

Avoid keeping the unit in direct sunlight for a long period of time. 

 

The heater is designed to be used at temperatures above -20°C.  If it is exposed 
to temperatures below this, it must be allowed to warm above this level before 
operation. 

 

Do not attempt to repair, disassemble or modify the appliance.  This unit contains 
no user-serviceable parts.  

 

Always unplug or disconnect the appliance from the mains power supply when 
not  in  use,  or  when  moving  or  cleaning  it.    Do  not  pull  the  cord  to  unplug  the 
heater.  

 

Keep the heater clean.  Do not allow any object to enter the ventilation or exhaust 
opening as this may cause electric shock, fire, or damage to the heater.  

 

Do not use the appliance for anything other than its intended use.  It is designed 
for domestic indoor use only.  

 

There may be a trace of odour during the first few minutes of initial use, or after 
a period of storage.  This is normal and will quickly disappear.  

 

This appliance has hot and arcing or sparking parts inside.  Do not use it in areas 
where gasoline, paint, or any flammable liquids are used or stored.  

 

Never locate this appliance where it may fall into a bathtub or otherwise become 
exposed to water.  

 

This appliance is IP24 rated, and so can be used or installed within a bathroom 
as long as the appliance and its cables are not within Zones 0-2. 

 

If  used  within  a  bathroom,  the  circuit  must  be  protected  by  a  suitable  RCD  to 
prevent electric shock. 

 

Do not allow the appliance to be submerged or sprayed with water. 

 

If  the  unit  is  wall-mounted,  it  must  be  installed  in  accordance  with  current 
regulations for the area of installation. If unsure, professional advice should be 
sought. 

 

The remote contains a lithium battery, keep out of reach of small children.  Seek 
medical advice if swallowed. 

 

To prevent battery leakage: Remove the battery from the remote if exhausted or 
before long periods of storage.

 

 

 

WARNING:  To  reduce  the  risk  of  fire  or  electrical  shock,  DO  NOT  use  this 
appliance  with  any  solid-state  Speed  Control  Device  or  any  variable  speed 
controllers.  

 
ENERGY SAVING AND UNIT SAFETY PROTECTION TIP 

 

Do not cover or restrict the airflow. Do not use in a dusty environment. 

 

For safety and maximum performance, when used as a portable unit the minimum 
distance from a wall or objects should be 50cm.  

Summary of Contents for EPMH1000LED













Reviews: