75530 0106 GB
c) Teaching-In – Multi Channel Transmit-
ter to Multi Channel Transmitter
1. Connect the source transmitter to the
target transmitter using the programming
cable.
2. Press and hold button 2 on the target
transmitter until LED D lights up.
3. Press the ENTER button. LED D flashes
slowly.
4. Either enter the channel number on the
target transmitter (direction function) or
press the impulse button, which is to be
taught in again, on the target transmitter
(impulse function).
Then press and hold the ENTER button
until the teach-in process has been
completed (see step 5).
5. On the source transmitter, either enter
the channel number then press and hold
the ENTER button (direction function) or
press and hold the impulse button,
whose code is to be transferred, on the
source transmitter (impulse function).
LED D on the target transmitter flashes
rapidly and lights up for approx. 3
seconds once the teach-in process has
been completed.
Release both buttons.
6. Remove the programming cable.
Aborting the teach-in process
•
Press the UP or DOWN button.
Duplicating
1. Connect both Multi Channel Transmit-
ters using the programming cable.
2. Press and hold the 0 button on the
target transmitter until LED C lights up
(approx. 5 seconds).
3. Then press and hold the ENTER button
on the target transmitter.
LED C flashes slowly.
4. Press the 0 button on the source trans-
mitter followed by the ENTER button
within 10 seconds. The coding is trans-
ferred and LED C on the target transmit-
ter flashes rapidly for approx. 70
seconds. LED C on the source transmit-
ter flashes slowly.
5. Release both buttons.
If LED C on the target transmitter lights
up for approx. 3 seconds, then the dupli-
cating process has been completed.
6. Remove the programming cable.
Aborting the duplicating process
•
Press the UP or DOWN button.
Caution!
Please note that all data already transferred
have been stored in the target transmitter!
Random Coding
1. Insert the programming cable into the
socket on the Multi Channel Transmitter,
and at the other end of the cable short-
circuit one of the outer pins with the
middle pin.
1
2
3
A
D
C
B
5
7
9
ENTER
6
8
0
4
2. Press and hold button 1 until LED B
lights up.
3. Briefly press the ENTER button. LED B
flashes slowly.
4. Press the impulse button or enter the
channel number at this point for which a
new random code is to be set.
5. Press and hold the ENTER button. LED
B flashes rapidly.
If LED B stays lit up then the coding
process has been completed and the
ENTER button can be released.
6. Remove the programming cable.
Caution! The new coding must be trans-
ferred to the radio control!
Replacing the Batteries
1. Unscrew the battery housing cover.
2. Remove the old batteries.
3. Insert two new 3 V batteries. Use only
batteries of type CR2032.
Make sure the polarity is correct!
4. Screw the battery housing cover back
on.
Caution!
Keep batteries out of reach of children!
Troubleshooting
•
The LEDs are only faint when lit up:
Change the batteries.
•
The LEDs do not light up at all:
Check the polarity of the batteries.
•
Move closer to the radio control or
teach-in the Multi Channel Transmitter
channels to the radio control(s) again.
Cleaning
Wipe the housing carefully with a damp lint-
free cloth.
Caution!
Do not use solvent-based cleaning agents.
These can damage your health and destroy
the surface of the housing.
Disposal
Waste electrical products and batteries
should not be disposed of with house-
hold waste!
Dispose of the waste product via a
collection point for electronic scrap
or via your specialist dealer.
Dispose of used batteries in a
recycling bin for batteries or via the
specialist trade.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Warranty
Within the statutory warranty period we
undertake to rectify free of charge by repair
or replacement any product defects arising
from material or production faults.
Any unauthorized tampering with, or modifi-
cations to, the product shall render this
warranty null and void.
Conformity
This product conforms to the basic
requirements of the R&TTE Direc-
tive 1999/5/EC.
For use in: EU/CH/FL/N/IS
The Declaration of Conformity can be found
on the Internet at: www.eldat.de.
Customer Service
If, despite correct handling, faults or mal-
functions occur or if the product was dam-
aged, please contact the company at the
address below:
ELDAT GmbH
Im Gewerbepark 14
D-15711 Zeesen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Website: www.eldat.de
e-mail: [email protected]
