background image

GB

Wired Weather Sensor

SW01-W

wind 

SWS01-W

wind-sun 

SWSR01-W

wind-sun-rain 

Model

SW01-W01-01

wind

SWSR01-W01-01

wind/sun/rain

SWS01-W01-01

wind/sun

Coding:

EasywaveSens

Power supply:

230 V AC ~ 50 Hz 

Connected load:

4 VA

Degree of protection:

IP44

Class of protection:

II

Data line:

max. 25m

Operating temperature:

-25 °C bis +55 °C 

Measuring ranges:
- wind

3 km/h to 50 km/h

- light intensity

1 lx to100 klx

Dimensions (BxLxH):
- sensor

52/131x200x73 mm

- plate 

121x52x30 mm

Weight:

260 g

 Technical Details

- 1 Sensor SWSR01
- 1 Mounting plate
- 2 Cover caps
- 1 Terminal cover
- 1 Terminal block 2-pin
- 2 Hex bolts 6x40
- 2 Washers
- 2 Dowels SX8 
- 1 Hexagon socket screw M6x65
- 1 Lock nut M6
- 2 Pan head screws
- Operating instructions

Scope of Delivery

The  weather  sensors  are  only  for  wire  trans-
mission of weather data to the Easywave radio 
receivers  RCJ05,  RCM04  or  CM01  for  weat-
her-dependent  control of awnings.

The manufacturer  shall not be liable for any da-
mage  caused  by  improper  or  non-intended 
use!

Intended use

Safety Advice

Before  you  connect  and  operate   

the  device,  please  read  these 
operating instructions carefully!

The  electrical  installation  must  only  be 
carried out by a qualified electrician (please 
refer  to  VDE  0100-200  and/or  relevant 
national regulations).
Repair, maintenance and cleaning 
work must only be carried out after 
the device has been disconnected 
from the mains power supply!
Have faulty device checked by the 
manufacturer!
Do not make any unauthorized alterations or 
modifications to the device!
Keep the device out of the reach of children.

-

-

-

-

-

Function

The  weather  sensors  continuously  detect  wind 
strength, light intensity and rain data and send 
this  data  via  a  wired  connection  to  the  control 
RCM04,  RCJ05  or  CM01.  There,  the  data  is 
evaluated  and  the  awning  is  controlled  accor-
dingly. 

The  „gastronomy  function“  integrated  in  the 
SWSR01 also allows the awning to be opened 
in  rainy  weather,  contrary  to  the  standard  rain 
function.

When selecting a location for the device, please 
ensure that the light sensor and surface of the 
rain sensor are not covered or placed in the 
shade. Slipstreams should also be avoided.

We recommend assembling the 

weather sensor at a height of above 
2.50 m. The installation height may by 
no means fall below 1.70 m.

For each installation, please ensure that 

the weather sensor is horizontal or is 
tilted downwards slightly at the front. 
The impeller must always face 
downwards.

1. Screw  the  mounting  plate  to  the  installation 

site with the screws and dowels.  

2. Insert  the  current  and  voltage-free  mains 

cable  and  the  Sensor  cable  through  the 
terminal  cover  from  below  and  clamp  the 
wires to the terminal block provided.

3. Attach the terminal to the pin connector on the 

printed  circuit  board  and  securely  fix  the 
terminal cover (see also „Electrical connecti-
on“).

4. Place the sensor between the brackets of the 

Mounting  plate  and  attach  it  with  hexagon 
socket  screw  and  the  lock  nut.  Attach  the 
cover caps.

 

Mains power cable
(not included in supply package)

Warning:

 the “Electrical connection” 

section of this document must be 
observed!

Terminal block 2-pin

Cover cap

Mounting plate

Installation

Light sensor 

(only SWSR01-W and 
 SWS01-W)

Rain sensor 

(only SWSR01-W)

Vane

SWSR01-W

Terminal cover

Sensor connection cable (data cable)
max. permitted Line 25 m
(not included in supply package)

Fig. 1

Reviews: