manualshive.com logo in svg

Elation Waterfall 250 Pro, Manual, Page: 4 / 35

Share
Download
Elation Waterfall 250 Pro Manual Download Page 4

 
 
 

Waterfall 250 Pro™ 

©Elation Professional®                                                                                                      4                                             

                                               

Waterfall 250 Pro™ 

Contents 

 

1. General 

Information……………………………………………………………………… 

3 

a. Introduction………………………………………………………………………. 

3 

b. Unpacking………………………………………………………..…………..… 3 

c. Customer 

Support…………………………………………….………………… 

3 

d. Warranty 

Registration……………………………………………………..…… 4 

e.  Discharge Lamp Warning………………………………………………………  4 

2. Safety 

Instructions………………………………………………………........…………. 7 

3. Features…………………………………………………………………………………… 

9 

4. General 

Guidelines………………………………………………………………………. 

10 

5. Lamp 

Installation…………………………………………………………………………. 

11 

a. Lamp 

installation…………………………………………………….………….. 

11 

b. Lamp 

optimization……………………………………………………..………… 

12 

6.  Mounting and Installation………………………………………………………….……. 14 

a. Mounting 

Positions……………………………………………………………… 

14 

b. Mounting 

Points…………………………………………………………………. 

15 

c. Securing………………………………………………………………………….. 

16 

7. Understanding 

DMX……………………………………………………………………... 17 

a. DMX 

Connections………………………………………………………………. 

17 

b. DMX 

Terminator…………………………………………………………………. 

18 

c.  3-Pin to 5-Pin Conversion………………………………………………………. 19 

d. DMX 

Addressing………………………………………………………………… 

19 

8. Display 

Indicators……………………………………………………………………….. 

21 

9. Fixture 

Menu……………………………………………………………………………… 

22 

a. Menu 

functions………………………………………………………………….. 

24 

10. DMX Channel Traits…………………………………………………………………….. 39 

a.  DMX Channel Values…………………………………………………………… 40 

11. Error Codes………………………………………………………………………………. 42 

12.  Cleaning and Maintenance……………………………………………………………… 44 

13. Warranty…………………………………………………………………………………... 45 

14. Photometric Data………………………………………………………………………… 47 

15. Gobo Patterns……………………………………………………………..……………... 48 

16. Dimensional Drawings………………………………………………….……………….. 48 

17. Circuit Schematic………...………………………………………………………………. 

49 

18. Technical Specifications…………………………………………...………….………… 50 

 

Summary of Contents for Waterfall 250 Pro




































Reviews:

No comments