5
4
3
2
1
1
2
3
4
Replacing the lamp
DANGER TO LIFE!
Only install the lamp with the device switched off! Unplug from mains before!
CAUTION!
The lamp has to be replaced when it is damaged or thermally deformed due to the heat!
The lens must be replaced if it is visibly damaged and therefore operating with reduced efficiency.
Before replacing the lamp, unplug mains lead and let the lamp cool down (approx. 5 minutes).
During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp
manufacturer’s notes!
Do not install lamps with a higher wattage! Lamps with a
higher wattage generate temperatures the device was not
designed for. Damages caused by non-observance are not
subject to warranty.
For the installation, you need one HMI lamp with up to max.
575W.
Procedure:
Step 1: Open the Service Lid on the top of the device
by unscrew the one screw.
Step 2: Loose the two screws at the two ends of the lamp.
Step 3: Remove the old lamp.
Step 4: Install a same type lamp into the lamp-socket,
fasten the two screws by hands.
Step 5: Close the Service Lid and screw the screw.
Installing
The installation of the device has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch
net. This secondary safety attachment must be constructed in a way that
no part of the installation can fall down if the main attachment fails.
Caution:
Devices may cause severe injuries when crashing down! If you
have doubts concerning the safety of a possible installation, do NOT
install the device!
DANGER OF FIRE!
When installing the device, make sure there is no
highly inflammable material (decoration articles, etc.) within a distance of
min. 0.5 M.
Mount the device with the mounting-bracket to your standing system. The
hole in the mounting bracket has a diameter of 13 mm.
Adjust the desired inclination-angle via the mounting-bracket and fix
the fixation screws.
DANGER TO LIFE!
Before taking into operation for the first time, the
installation has to be approved by an expert or by qualified
ENGINEERS/TECHNICIANS only!
Connection with the mains
DANGER TO LIFE!
The electric connection must only be carried out by a qualified electrician!
In order to connect the device to the mains, you have to install a power-plug.
The occupation of the connection-cables is as follows:
Cable
Pin
International
Brown
Live
L
Blue
Neutral N
Yellow/Green Earth
The earth has to be connected!
Connect the device to the mains with the power-plug.
If the device will be directly connected with the local power supply network, a disconnection switch with
a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
Lighting effects cannot be connected to dimming-packs.
DANGER TO LIFE!
Before taking into operation for the
first time, the installation has to be approved by an
expert!
OPERATION:
After you connected the fixture to the mains,
the lamp will be on. Please see the right figure,
you can adjust the 1, 2, 3, 4 four places to
center the lamp in the reflector, and you
adjust beam field by pulling and pushing the
handle screw through the track on the top of
the device.
CLEANING AND MAINTENANCE
The following points have to be considered
during the inspection:
1)All screws used for installing the devices or
parts of the device have to be tightly connected
and must not be corroded.
2)There must not be any deformations on housings,
fixations and installation spots(ceiling, suspension.
trussing).
3)The electric power supply cables must not show any damages, material
fatigue (e.g. porous cables) or sediments. Further instructions
depending on the installation spot and usage have to be adhered
by a skilled installer and any safety problems have to be
removed.
DANGER TO LIFE!
Disconnect from mains before
starting maintenance operation!
We recommend a frequent cleaning of the device.
Please use a moist, lint-free cloth. Never use alcohol or
solvents!
The interior of the device should be cleaned at least
annually using a vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device except for the lamp. Maintenance and service
operations are only to be carried out by authorized dealers.
Please refer to the instructions under “Replacing the lamp”.
Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers
only in order to avoid hazards.
Should you have further questions, please contact your dealer.
TECHNICAL SPECIFICATIONS
Made in China
Power supply:
Max. 230/240V/AC, 50Hz
Power consumption,
Max. 600W
Dimensions (L x W x H);
890x330x520mm
Weight;
23 kg
Fitting lamp
HMI 575W Lamp
Maximum ambient temperature t
a
: 25°C
Maximum housing temperature t
S
: 130°C
Minimum distance:
2m
Fuse:
6.3A 250V
Ballast
Cooling Fan
HMI 575 Lamp
Service Lid
