background image

 

© 2022 ELATEC GmbH – TWN4 MultiTech Nano LEGIC 42 M user manual DocRev4 – 04/2022 

 

Page 

3

 of 

12

 

 

1

 

INTRODUCTION 

1.1

 

ABOUT THIS MANUAL 

 

This user manual is intended for the user and enables a safe and appropriate handling of the product. It gives a general overview, as 

well  as  important technical data and safety information about the product. Before using the product, the user should read and 

understand the content of this user manual. 

 

For the sake of better understanding and readability, this user manual might contain exemplary pictures, drawings and other 

illustrations. Depending on your product configuration, these pictures might differ from the actual design of your product. 

 

The original version of this user manual has been written in English. Wherever the user manual is available in another language, it is 

considered as a translation of the original document for information purposes only. In case of discrepancy, the original version in 

English will prevail. 

 

1.2

 

SCOPE OF DELIVERY 

 

1.2.1

 

COMPONENTS AND ACCESSORIES 

 

Depending on your product configuration, the product can be delivered alone or with different components and accessories, such as 

cables or wall holders, as part of a kit. For more information about the delivered components and accessories, refer to your delivery 

note, consult the ELATEC website or contact ELATEC. 

 

1.2.2

 

SOFTWARE 

 

The product is delivered ex-works with a specific software version (firmware), which can be found on the packaging label, on the 

delivery note or other delivery documents. 

 

1.3

 

ELATEC SUPPORT 

 

In case of any technical questions, refer to the ELATEC website (www.elatec.com) or contact ELATEC technical support at 

[email protected] 

 

In case of questions regarding your product order, contact your Sales representative or ELATEC customer service at 

[email protected] 

 

1.4

 

REVISION HISTORY 

 

VERSION 

CHANGE DESCRIPTION 

EDITION 

04 

Chapter “Compliance Statements” updated 

04/2022 

03 

Product pictures updated 

03/2022 

02 

Chapters “Software”, “Technical Data”, “Compliance Statements” and “Labeling” updated 

01/2022 

01 

First edition 

12/2021 

 

 

 

Summary of Contents for TWN4 MULTITECH NANO LEGIC 63 M













Reviews: