background image

2 of 8 

I

NSTALLATION 

O

VERVIEW

 

!!! IMPORTANT !!! 

When installing an MRA-664 that has previously been configured in stand-alone mode, its configuration MUST be 
reset to its default (unconfigured) state.  Doing this requires version 1.4.5xx or greater of the MRA software.  Once 
installed, enter PIN code 1354 in the Configuration Wizard to access a configuration reset button. 

 

Using KP7 Keypads:  Older versions of the MRA Software have a communication device for the KP7 that can interfere 
with the communication device in ELAN, resulting in incorrect feedback when saving favorites.  Version 1.4.5xx and 
above of the MRA software correct this issue. 

I

NSTALL 

S

YSTEM

1.  During the rough-in phase, install speaker wire for the speakers in each zone. 

2.  Also during the rough-in phase, run a Cat5 wire from the location of the Zone Controller to the Managed Switch, and a Cat5 

from the Managed Switch location to the Network Assembly as needed. 

3.  Mount the speakers and keypads in each zone, and install the Zone Controller and the sources. 

4.  Setup the SpeakerCraft.   

5.  Connect the ELAN system to the SpeakerCraft system electrically. See the Wiring Diagrams for more information. 

6.  Configure the ELAN

 

system

 

for the SpeakerCraft and confirm communication between it and the ELAN

 Controller

. See 

ELAN Configuration details below. 

7.  Test the system by changing sources in a zone to confirm the correct source plays, and by testing the ELAN interface 

transport controls. 

C

ONNECTION 

D

IAGRAM

 

g! Controller

External Sources

Preamp Out/Speaker Out

SpeakerCraft MRA664

1

3

Network Assembly

2

CAT5 

Cable

4

Zone 5/6 Preamp Out Only

P
A
G
I
N
G

 

B

ILL 

O

M

ATERIALS 

 

#

D e v ic e

M a nuf a c t ure r

P a rt  N um be r

P ro t o c o l

C o nne c t o r T ype

N o t e s

1

SpeakerCraft M RA 664

Niles

M RA 664

TCP /IP

RJ45 Female

2

Cat5 Cable A ssy.

Installer

N/A

TCP /IP

RJ-45 M ale X RJ-45 M ale

M ust co nnect all 8 wires

3

Netwo rk A ssembly 

ELA N

NWA 18

TCP /IP

RJ-45 Female

o r ro uter/switch

4

g! Co ntro ller

ELA N

Vario us (Ex. gSC10)

TCP /IP

RJ45 Female

 

Summary of Contents for SpeakerCraft MRA664









Reviews: