Elan HC-600 ODG V1 User Manual Download Page 2

©ELAN (Changzhou) Hardware Co. Ltd.   

Version 2.1, September 2012   

 
 

WARNINGS   

1

 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 
concerning use of the appliance by a person responsible for their safety. 
2

 

Children should be supervised to ensure that they do not play with the appliance. 

3

 

Care is needed when handling cutting blades during cleaning. 

4

 

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly 

qualified person in order to avoid a hazard. 

 

 

Correct Disposal of this product 

This marking indicates that this product should not be disposed with other household wastes throughout the EU. 
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it 
responsibly to promote the sustainable reuse of material resources. To return your used device, please use the 
return and collection systems or contact the retailer where the product was purchased. They can take this product 
for environmental safe recycling. 

 

Warranty Information 

The manufacturer provides warranty in accordance with the legislation of the customer's own country of residence, 
with a minimum of 1 year (Germany: 2 years), starting from the date on which the appliance is sold to the end 
user. 
The warranty only covers defects in material or workmanship. 
The repairs under warranty may only be carried out by an authorized service centre. When making a claim under 
the warranty, the original bill of purchase (with purchase date) must be submitted. 
The warranty will not apply in cases of: 
Normal wear and tear Incorrect use, e.g. overloading of the appliance, use of non approved accessories Use of 
force, damage caused by external influences Damage caused by nonobservance of the user manual, e.g. 
connection to a nun suitable mains supply or non compliance with the installation instructions Partially or 
completely dismantled appliances 

Summary of Contents for HC-600 ODG V1
















Reviews: