3
i
!
!
!
Connection of the KNX bus line
The connection of the KNX bus line is made with the ter-
minal block (red / black) included in delivery and inserted
into the slot at the bottom of the housing.
Characteristics of the KNX terminal block
• spring clamping of conductors
• 4 seats for conductors for each polarity
• terminal suitable for KNX bus cable with single-wire
conductors and diameter between 0.6 and 0.8 mm
• recommended wire stripping approx. 5 mm
•
color codification: red = + (positive) bus conductor,
black = - (negative) bus conductor
Warning!
The electrical connection of the device can
be carried out only by qualified personnel. The incor
-
rect installation may result in electric shock or fire.
Before making the electrical connections, make sure
the power supply has been turned off.
Configuration and commissioning
Configuration and commissioning of the device require
the use of the ETS® (Engineering Tool Software) program
V4 or later releases. These activities must be carried out
according to the design of the building automation system
done by a qualified planner.
Note.
The configuration and commissioning of KNX
devices require specialized skills.To acquire these
skills, you should attend the workshops at KNX certi-
fied training centers.
Configuration
For the configuration of the device parameters the corre
-
sponding application program or the whole ekinex® pro-
duct database must be loaded in the ETS program. For
detailed information on configuration options, refer to the
application manual of the device available on the website
www.ekinex.com.
Code
Application program
(## = version)
EK-BO1-TP-RMA
APEKBO1RMATP##.knxprod
Commissioning
For commissioning the device the following activities are
required:
• make the electrical connections as described above;
• turn on the bus power supply;
• switch the device operation to the programming mode
• by pressing the programming pushbutton located on
the front side of the housing. In this mode of operation,
the programming LED is turned on;
• download into the device the physical address and the
configuration with the ETS® program.
At the end of the download the operation of the device
automatically returns to normal mode; in this mode the
programming LED is turned off. Now the bus device is
programmed and ready for use.
Reset of the device
To reset the device remove the bus connection by ex-
tracting the bus terminal from its seat. Keeping pressed
the programming pushbutton, reinsert the bus terminal in
his seat; the programming LED blinks fast. Release the
programming button and remove the bus terminal again;
the reset was carried out. Now you need to address and
configure again the device via ETS.
Warning!
The reset restores the device back to the
state of delivery from the factory. The address and
the value of the parameters set during confi guration
will be lost.
Marks
• KNX
• CE: the device complies with the Low Voltage Directi-
ve (2014/35/UE) and the Electromagnetic Compatibility
Directive (2014/30/UE)
Maintenance
The device is maintenance-free. To clean use a dry cloth.
It must be avoided the use of solvents or other aggressive
substances.
Disposal
At the end of its useful life the product described in this da-
tasheet is classified as waste from electronic equipment
in accordance with the European Directive 2012/19/UE
(WEEE), and cannot be disposed together with the muni-
cipal undifferentiated solid waste.
Warnings
•
Installation, electrical connection, configuration and
commissioning of the device can only be carried out
by qualified personnel in compliance with the appli
-
cable technical standards and laws of the respective
countries
• Opening the housing of the device causes the imme-
diate end of the warranty period
• In case of tampering, the compliance with the essen-
tial requirements of the applicable directives, for which
the device has been certified, is no longer guaranteed
• ekinex
®
KNX defective devices must be returned to the
manufacturer at the following address: Ekinex S.p.A.
Via Novara 37, I-28010 Vaprio d’Agogna (NO)
Other information
• The instruction sheet must be delivered to the end
customer with the project documentation
• For further information on the product, please contact
the ekinex
®
technical support at the e-mail address:
[email protected] or visit the website www.ekinex.
com
• KNX
®
and ETS
®
are registered trademarks of KNX
Association cvba, Brussels
© Ekinex S.p.A. 2020. The company reserves the right to make chan-
ges to this documentation without notice.
Warning!
Incorrect disposal of this product may cau-
se serious damage to the environment and human
health. Please be informed about the correct disposal
procedures for waste collecting and processing provi-
ded by local authorities.