background image

ITS Partner O.B.S S.L · Av. Cerdanyola 79-81 Local C 

08172 Sant Cugat del Vallés · Barcelona (Spain)  

Phone: +34935839543  ·  [email protected]  ·   www.ek.plus

 

11

 

 

 

CM 8SH CI-TC 

USER MANUAL

 

 

Program pool: 

In this table all channels, services, which correspond to the selected entries will be listed. From here the 
services that are wished to be assigned to each MUX output can be selected. Each service is assigned 
to the input tuner from which it has been tuned. 

S.I.D.: S.I.D. (Service Information Descriptor) assigned at source to that service. 

Service name: name assigned to the service at source. Next, a symbol appears indicating whether the 
service is TV or Radio, and whether it is encrypted or open. 

DECODIFIC.: This module is provided with two slots to insert two CAMs. By clicking on it, we activate or 
not the service so that it decodes in the selected CAM. 

See an example

.MODULATION: each circle corresponds to a MUX output: 1, 2, 3 or 4. By clicking on that circle, it changes 
from red to green, and this service is assigned to a MUX output. 

DVB-T output card: 

This part of the menu consists of three differentiated sections: 

 

N.I.T. (Network Information Table) parameters 

 

RF output channel parameters 

 

Information window on the throughput of each MUX output 

N.I.T. parameters: 

 

Vers.: N.I.T. version 

 

O.N.I.D.: Original Network Identification Descriptor. 

 

N.I.D.: Network Identification Descriptor. 

 

L.C.N.: Logical Channel Number. LCN type selection (EACEM for Europe, ITC for the United 
Kingdom 

…)

 

 

Network Name: identifies the name of the local DTT (Digital Terrestrial Television) network. 

RF output channel parameters: 

 

Freq. (KHz): Center frequency, in KHz, of the desired output channel. E.g. CH21=474000 

 

Id. T.S.: T.S. identifier, in general, it is not necessary to change the identifier. 

 

Const.: Constellation. Select the desired output constellation: 64QAM, 16QAM, QPSK. 

 

Band: Output channel bandwidth: 7MHz or 8MHz. 

 

F.E.C.: (Forward Error Correction). Select the error correction level: 7/8, 5/6, 3/4, 2/3, 1/2. 

 

Guard Int. Select guard interval: 1/32, 1/16, 1/8, 1/4. 

 

Atten. Level: The power level of the modulator is 95dBuV; it can be adjusted 20dB by using 
this attenuator. 

 

 

Summary of Contents for 082256

















Reviews: