eisl EL-BAD-TH-UNI 1018, Installation Instructions Manual

Page: 7 / 19

7
GB
Installation instructions
Dear customer,
You have purchased a high-quality and long-lasting product
from our line of goods. Please read these instructions
carefully before assembling and observe the notes.
Therefore, keep the instructions in a safe place and pass
them on to possible subsequent owners.
Safety notes
• Only allow experts carry out the installation work.
• CAUTION DAMAGE BY WATER!
Prior to installation please turn the general water supply
off.
• Ensure that all gaskets have the correct fit.
• These taps are not suitable for use on low pressure and
small electrical storage heaters.
• We recommend the installation of a filter into the appli-
ance or at least the use of angle valves with filter, in order
to avoid the inflow of foreign matter, which could damage
the upper parts of the valves.
• This tap is only intended for use in private households!
Only suitable for use in rooms with a temperature over 0 °C,
when there is danger of frost, sut off the water supply and
empty the tap.
• Take care when adjusting the warm water. Danger of
scalding!
• Incorrectly installed fittings can cause water damages!
• Despite careful production, sharp edges can occur. Please
exercise caution!
Disposal
Your washbasin tap is delivered in a solid packaging, in or-
der to protect it against transport damages. The packaging
consists of recyclable materials. Dispose it in an environ-
mentally suitable manner.
Do not throw the product into the normal domestic waste
at the end of its service life, but ask your municipal
administration about the possibility of an environmentally
friendly disposal.
Technical data
• Flow pressure: Recommended as 1.5 to 6 bar; in case of
more than 6 bar connection pressure, we recommend that
a pressure reducer is installed
• Water temperature: max. 80 °C
Installation Instructions
• After installing the tap please unscrew the mixer nozzle,
flush the pipeline and the tap thoroughly for a longer time,
in order to flush out contaminations and residues.
• Check all connections carefully after first-time use to make
sure that they are tight.
• We do not assume any warranty for incorrect installation -
in particular for subsequent damages!
Instructions for care
Sanitary taps require special care. Therefore, please observe
the following instructions:
• Chrome-plated surfaces are sensitive to lime-dissolving
agents, acidic cleaning agents and all kinds of abrasives.
• Never clean coloured surfaces with abrasive, corrosive, or
alcoholic agents.
• Only clean your taps with clear water and a soft cloth or a
shammy.
Do not forget to unscrew the mixing nozzle
in regular intervals and to remove possibly
calcareous residues or foreign matter. It is
advisable to replace the mixing nozzle with a new one in the
case of extreme contamination.
Maintenance
• Please note that a valve top is a wearing part and that in
the case of very hard or soiled water the valve must be
replaced every 1 to 2 years, as required.
You will find illustrated instructions on how to replace the
valve bonnet on our website under the following link:
web.eisl.at/qrcode/Austausch_Kartusche-
Ventiloberteil_Eisl.pdf
• Please check all joints and connections for leaks or visible
damages at regular intervals.
• In case of any leaks or visible damages to the fitting or
connection hoses, these should be immediately checked
by a specialist and replaced if necessary.
Decommissioning
• Cut off the water supply before dismantling the product.
• Pay attention to escaping residual water.
• Disassemble the product in the reverse order of the as-
sembly instructions.

The illustrations are to be considered as figurative
representations, deviations of the product are possible.
Subject to technical modifications.
WARRANTY CARD
The Eisl Sanitär GmbH, based in Wallenhorst, shall take on a
manufacturer’s warranty for the product you have procured
in accordance with the warranty conditions stated below.
Your legal warranty claims from the purchase contract with
the seller and your legal rights shall not be limited by this
warranty.
Warranty conditions:
1. Scope of warranty
The Eisl Sanitär GmbH shall grant a warranty for proper
material qualities and material processing in accordance
with the intended purpose as well as professional assembly,
tightness and function. The warranty shall only apply for the
country in which the product has been procured.
Included within the scope of the warranty is a guarantee,
reduced to 1 year, for the durability of non-high-gloss
chrome-plated surfaces, such as bronzed or coloured
surfaces.
Excluded from the warranty are the following:
• Corrosion in the mixer jets (aerator)
• Valve bonnet
• Damages due to improper assembly, commissioning and
handling
• Damages due to external influences such as fire, water and
chemical influences