Measured noise value
The A-valued machine’s noise level typically is::
Nois pressure level = 87 dB (A). Noise power level = 100 dB (A).
Measured vibration value
The valued acceleration typically is 7 m/s²
Usage
This angle grinder can be used for separating and grinding many different materials, e.g.
metal or stone. In case of doubt please read the manufacturer’s instructions. Do not use this
Mains connection
Connect only to a single-phase AC current supply and only to the mains voltage specified on
the rating plate. Connection to sockets without earth protection is possible as the appliance
features protective insulation to DIN 57740/VDE 0740 and CEE 20. Radio suppression com-
plies with the Europe an standard EN 55014. W hen fitting the plug, make sure that the brown
(live) wire of this appliance is connected to the plug terminal marked L or coloured red, and
the blue (neutral) wire of this appliance is connected to the plug terminal marked N or col-
oured black. Under no circumstances must the wires of this appliance be connected to the
earth terminal of the plug marked either E, with the earth symbol, or coloured green or
green/yellow .
Smooth start
The electronic smooth start will prolong the life of both the motor and the gears.
Switching on and off
Switching on: Push the sliding switch forward. To lock, depress the front part of the switch.
Switching off: To unlock, depress the back part of the sliding switch. The switch will automati-
cally move back to "0".
Electronic
The number of revs is adjusted electronically when the load increases.
In case of a longer overload period the speed is decreased electronically. The machine contin-
ues to run slowly to cool down the motor coil. After switching off and on the machine can be
used at rated load. The duration of cooling-down period depends on the gra de of overload.
Speed selection (A G 1300-125 XE)
Spee d pre-selection with the setting wheel:
A = lowest speed
G = highest speed
Mounting the protective cover
Open the clamping lever. Push the protective cover over the gear neck, if necessary slightly
loosen the nut of the tension screw.
Fitting the working tool
Always disconnect the plug from the socket before carrying out any work on the machine.
Maintenance
Keep the machine and the ventilation slots clean.
Only use Original accessories and spare parts. Should components which have not been de-
scribed need to be exchanged please contact one of our Atlas Copco service agents.
Service agents
Worldwide service by Atlas Copco. The corresponding addresses are to be found in the at-
tached brochur e.
Protective cap with clamping lever
Align the protective cap as required and fasten the clamping lever. If the protective cap is not
tight enough, open the clamping lever, slightly fasten the nut of the tension screw and re-
fasten the clamping lever.
The protective cap must no t be movable when the clamping lever is locked. Take
care that the g rind ing disk can be f reely tu rned.
Technical data
1.520 Watt, 220 – 240 V, 50 – 60 Hz. Continuous speed control by speedo ge nerator
(constant number of revs). Weight approx. 2,4 kg.
FIXTEC-quick-action adjusting nut
Customary adjusting nut
Lock the work spindle by depressing the spindle lock. Mount the tension flange, the working
tool, and the adjusting nut as shown in illustration.
Only tighten and loosen the
FIXTEC
quick-action adjusting nut by hand.
Do not u se any
tools!
Insure that the hoop of the FIXTEC quick-action adjusting nut is only placed in the
upward position for tightening/looseni ng. Loosen respectively tighten the adjusting nut with a
pin-type face spanner
Guarantee
A 12 month guarantee (as from invoice date) is given for all technical and mechanical parts,
except in the case of outside culpability.
Spares can be sup plied accord ing to the list. We will carry ou t necessary repairs.
VARILEX
®
WSF 1600