GB
GB
- 29 -
c) If the cutting-off wheel jams or you inter
-
rupt your work, switch off the tool and
hold it still until the wheel has reached a
complete standstill. Never attempt to pull
the cutting-off wheel out of the cut whilst
it is still rotating, otherwise it may suffer
recoil.
Find and rectify the cause of the jam.
d) Do not switch the electric tool on again
whilst it is inside the workpiece. Allow
the cutting-off disk to reach its full speed
before you continue the cut with care.
Otherwise the wheel may catch, jump out of
the workpiece or cause recoil.
e) Support panels or large workpieces to
reduce the risk of recoil by a jammed
cutting-off wheel.
Large workpieces may
sag under their own weight. The workpiece
must be supported on both sides of the wheel
both near the cut and also at the edge.
f) Be particularly careful with “pocket cuts”
in existing walls or in areas which you
cannot see clearly.
As the cutting-off disk
enters the cut it may suffer recoil if it cuts into
gas or water pipes, electric cables or other
objects.
2. Layout and items supplied
(Figure 1)
2.1 Layout
1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Guard
5. Flange nut wrench
2.2 Items supplied
Please check that the article is complete as spe-
cified in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Important!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
•
Angle Grinder
•
Additional handle
•
Guard
•
Flange nut wrench
•
Original operating instructions
3. Proper use
The angle grinder is designed for grinding metal
and stone when using the appropriate grinding
wheel and guard.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case
of misuse. The user / operator and not the manu
-
facturer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
See waranty card of your country.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec
-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Fitting the additional handle (Fig. 2)
•
The angle grinder must not be used without
the additional handle (3).
•
The additional handle can be secured in any
of 2 positions (A, B).
Tool side
Suitable for
Left (position A / as
shown)
Right-handed users
Right (position B)
Left-handed users
5.2 Setting the guard (Fig. 3)
Warning!
•
Switch off the tool. Pull the power plug.
•
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
•
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
screw (a) and turn the cover (4) into the requi-
red position.
•
Ensure that the guard (4) correctly covers the
gear wheel casing.
•
Retighten the screw (a).
•
Ensure that the guard (4) is secure.
m
Take care that the safety device is secure.
m
Never use the angle grinder without the
guard.
Anl_SA_TC AG 115_1_SPK8.indb 29
Anl_SA_TC AG 115_1_SPK8.indb 29
01.10.2020 14:02:54
01.10.2020 14:02:54
