background image

GB

- 18 -

8. Cleaning, maintenance and 

ordering of spare parts

 

 Danger!

Pull the power plug before doing any 

cleaning and maintenance work on the ap-

pliance.

 Warning! 

Wait until the compressor has completely 

cooled down. Risk of burns!

 

Warning! 

Always depressurize the tank before carrying 

out any cleaning and maintenance work.

 

Danger!

After use, always switch o

  the equipment 

immediately and pull out the power plug.

8.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

• 

 You must disconnect the hose and any 

spraying tools from the compressor before 

cleaning. Do not clean the compressor with 

water, solvents or the like.

 8.2  Condensation water (Fig. 1)

Important. To ensure a long service life of the 

pressure vessel (2), drain o

  the condensed wa-

ter by opening the drain valve (11) each time after 

using. Check the pressure vessel for signs of rust 

and damage each time before using. Do not use 

the compressor with a damaged or rusty pressure 

vessel. If you discover any damage, please con-

tact the customer service workshop.

Important! 

The condensation water from the pressure 

vessel will contain residual oil. Dispose of the 

condensation water in an environmentally 

compatible manner at the appropriate collec-

tion point. 

8.3 Safety valve (10)

The safety valve has been set for the highest per-

mitted pressure of the pressure vessel. It is prohi-

bited to adjust the safety valve or remove its seal. 

Actuate the safety valve from time to time to en-

sure that it works when required. Pull the ring with 

su

  cient force until you can hear the compressed 

air being released. Then release the ring again. 

8.4 Check the oil level at regular intervals

Place the compressor on a level and straight 

surface. The oil level must be between the two 

marks MAX and MIN on the oil oil level window 

(Fig. 10,11).

Changing the oil: Recommended hydraulic oil: 

SAE 5W/40 or an alternative of the same quality.

It should be re

fi

 lled for the 

fi

 rst time after 10 hours 

of operation. Thereafter the oil should be drained 

and re

fi

 lled after every 100 hours in service.

8.5 Changing the oil

Switch o

  the engine and pull the mains plug out 

of the socket. After releasing any air pressure you 

can unscrew the oil drainage screw (15) from the

compressor pump. To prevent the oil from running

out in an uncontrolled manner, hold a small metal

chute under the opening and collect the oil in a

vessel. If the oil does not drain out completely, we

recommend tilting the compressor slightly.

Dispose of the old oil at a drop-o

  point for 

old oil.

When the oil has drained out, re-

fi

 t the oil draina-

ge screw (15). Fill new oil through the oil 

fi

 ller ope-

ning (13) until it comes up to the required level. 

Then replace the oil sealing plug (14).

8.6 Cleaning the intake 

fi

 lter (1)

The intake 

fi

 lter prevents dust and dirt being 

drawn in. It is essential to clean this 

fi

 lter after at 

least every 100 hours in operation. A clogged 

intake 

fi

 lter will decrease the compressor‘s per-

formance dramatically. Undo the screw on the 

air 

fi

 lter so that the halves of the air 

fi

 lter housing 

can be opened. Use compressed air at low pres-

sure (approx. 3 bar) to blow out all the parts of 

the 

fi

 lter and then assemble the 

fi

 lter in reverse 

order. When cleaning, take adequate precautions 

against dust (e.g. use a suitable face mask).

Anl_SA_TC_AC_190_24_8_SPK8.indb   18

Anl_SA_TC_AC_190_24_8_SPK8.indb   18

09.08.2016   13:39:51

09.08.2016   13:39:51

Summary of Contents for TC-AC 190-24-8





































Reviews: