GB
- 15 -
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
The equipment can be used in enclosed rooms
in a free standing position for room heating. Keep
a minimum distance of 1 m between the front
of the housing and walls, combustible materials
(furniture, curtains, etc.) and 30 cm from all other
housing surface areas. The equipment may only
be used completely mounted and standing verti-
cally on a stable surface. It is prohibited to opera-
te the equipment on an instable surface (e.g. on
a bed).
•
Check the correct air throughput by holding a
sheet of paper at a distance of 10 cm in front
of the air outlet grille in air circulation mode
(without heating). The paper must be blown
away from the air outlet grille.
•
When the equipment is used for the first time
or after a long period of rest it may emit an
odor for a short time. This is not a fault.
•
Because the heating system works with spe-
cially encapsulated heating elements and a
high air delivery rate, the emitted air may be
felt to be cooler than that from a conventional
fan heater. This is not an equipment defect.
6. Operation
6.1 Heat output switches (Fig. 1):
•
Off setting (0)
•
Fan setting (A)
•
Low heat output (B)
•
Maximum heat output (C)
6.2 Thermostat control (Fig. 1 / Item 2):
Note:
The fan will start as soon as the equipment is
switched on.
The equipment will only heat up when the room
temperature falls below the temperature set on
the thermostat and the heat output switch is on.
Switch on the required heating output. Turn the
control to “max” until the required room tempe-
rature has been reached. Then turn down the
control until you hear a clear click. The thermostat
will switch the heating element on and o
ff
auto-
matically.
6.3 Overheating guard
In case of excessive heating, the heating function
shuts down automatically. The fan will restart.
If this occurs, turn o
ff
the equipment, disconnect
the mains plug and wait a few minutes for the
equipment to cool. After eliminating the cause
(e.g. a covered air grille), the equipment can be
switched on again.
If the overheating guard triggers repeatedly,
please contact your customer service center (in
Germany ISC GmbH).
6.4 Switching o
ff
After the hot equipment has been switched o
ff
(by
turning the heat output switch to “0”) the fan may
continue to run for a while to cool the equipment.
However, if the fan continues to run for more than
10 minutes, this is a sign that it cannot cut out
automatically because of the high room tempera-
ture. In this case you must pull out the power plug.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
The equipment must have cooled down.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
Remove dust with a vacuum cleaner.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
Anl_EH_3000_SPK7.indb 15
Anl_EH_3000_SPK7.indb 15
23.04.2019 08:07:38
23.04.2019 08:07:38
Summary of Contents for EH 3000
Page 81: ...81 Anl_EH_3000_SPK7 indb 81 Anl_EH_3000_SPK7 indb 81 23 04 2019 08 07 45 23 04 2019 08 07 45...
Page 82: ...82 Anl_EH_3000_SPK7 indb 82 Anl_EH_3000_SPK7 indb 82 23 04 2019 08 07 45 23 04 2019 08 07 45...
Page 83: ...83 Anl_EH_3000_SPK7 indb 83 Anl_EH_3000_SPK7 indb 83 23 04 2019 08 07 45 23 04 2019 08 07 45...
