11
GB
5.2 Assembly
5.2.1 Assembling the equipment
Assemble the high-pressure cleaner as shown in
Figure 2-7.
5.2.2 Water inlet connector (Fig. 1/13)
The connection for the water inlet (13) is equipped
with a connector for standard hose coupling systems.
Attach the hose coupling on the supply hose (min. Ø
1/2“) to the connector for the water inlet (13).
An anti-vacuum device must be installed between
the water tap and the high-pressure cleaner! Ask
your local plumber about this.
5.2.3 Connecting the high-pressure hose
(Fig. 1-2; 5-6/18)
Remove the transport brace as shown in Figure 9
from the connection for the high-pressure hose (9).
Connect the high-pressure hose (18) to the
connection on the high-pressure cleaner (9) and on
the spray gun (14).
5.2.4 Fitting the gun attachments
The normal lance, the lance with rotating nozzle or
the foam nozzle can be attached prior to using the
high-pressure cleaner (Fig. 2).
Lance point / wide cone (16)
The shape of the water jet can be changed from
concentrated to flat jet by turning the nozzle (Fig. 9).
Lance with rotating nozzle (17)
To remove particularly stubborn dirt, use the lance
with rotating nozzle (17).
5.2.5 Electrical connections (Fig. 1)
쎲
Before you connect the appliance to the mains
supply make sure that the data on the rating
plate are identical to the mains data.
쎲
If you use any extension cables, make sure that
they are suitable for outdoor use and have large
enough wires:
1 – 10 m: 1.5 mm
2
10 – 30 m: 2.5 mm
2
쎲
Plug the mains plug (8) on the power cable (6)
into the mains socket outlet.
6. Operation
The equipment consists of an assembly with a pump,
which is encased in a shock absorbing housing. The
equipment comes with a lance and a non-slip gun
(for an optimal working position), whose shape and
configuration comply with the applicable regulations.
6.1 Using for the first time:
Once you have completely assembled the high-
pressure cleaner and connected all connections,
proceed as follows:
Open the water inlet. Press safety pin “a” (Fig. 2) on
the spray gun and pull back trigger lever “b” (Fig. 2)
in order to bleed the trapped air out of the device.
Turn on the device by switching the ON/OFF switch
(Fig. 1/12) to “I”.
To temporarily turn off, release the trigger lever (b),
at which point the device goes to standby. As soon
as you press the trigger lever again (b), the high-
pressure cleaner restarts.
To completely turn off the high-pressure cleaner,
switch the ON/OFF switch (Fig. 1/12) to “0”.
6.2 Using cleaning agent (Fig. 2;7):
Unscrew and remove the foam nozzle (7) from the
cleaning agent tank (15) (Figure 7). Fill a suitable
cleaning agent into the cleaning agent tank (15) and
replace the foam nozzle (7). Fit the foam nozzle (7)
to the pistol (14) as shown in Figure 2. The cleaning
agent will be added automatically.
6.3 Holder for the gun/accessories (Fig. 1;8)
The gun and accessories can be kept in the provided
holder (8/10) in order to save space when not in use.
7. Cleaning, maintenance and
ordering of spare parts
Important!
Always pull out the mains power plug before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
Anleitung_BT_HP_160_SPK1:_ 13.03.2008 9:24 Uhr Seite 11
