17
GB
Packaging:
The unit is supplied in packaging to prevent it from
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
When using the equipment, a few safety precau-
tions must be observed to avoid injuries and
damage.
Read the operating instructions carefully and
comply with them. It is important to consult
these instructions in order to acquaint yourself
with the unit, its proper use and safety regulati-
ons.
Keep this manual in a safe place, so that the
information is available at all times.
If you give the equipment to any other person,
give them these operating instructions as well.
We cannot accept any liability for damage or
accidents which arise due to a failure to follow
these instructions.
1. Safety regulations
The corresponding safety information can be found
in the enclosed booklet.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
2. Layout and items supplied (Figures
1a-1c)
1 Engine / gear unit
2 Reversing
starter
3 Steering handle holder
4 Guard
plate
5 Steering handle – clutch lever
6 Steering handle – throttle lever
7 Depth
stop
8 Clutch
lever
9 Bolts for spark plug boot
10 Spark plug wrench
11 Two hoe blades
12 Two limiting discs
13 Two axle covers
14 Transport wheel with holder
15 Strut for push bar
16 Fastening set for hoe blades and limiting discs
(four screws M8x35, four 8 mm spring rings, four
8 mm washers, four M8 nuts)
17 Fastening set for steering bar holder (four screws
M8x20, four 8 mm spring rings, four 8 mm wash-
ers)
18 Fastening set for steering bar (four screws
M8x30, four M8 nuts, four large 8 mm washers)
19 Fastening set for clutch lever (one screw M8x38,
one cap nut M8)
20 Fastening set for push bar strut (four screws
M8x35, four lock nuts M8)
21 Fastening set for guard plate (four screws M8x16,
four 8 mm spring rings, four 8 mm washers)
22 Fastening set for transport wheel (one screw
M10x65, one nut M10, one resetting spring, one
split pin)
23 Split pin for fastening the depth limiter
24 Fastening set for throttle lever (one screw M6x45,
one nut M6)
3. Intended use
The machine is designed for digging over beds and
fields. Be sure to observe the restrictions in the
additional safety instructions.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any
kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Environmental protection
Dispose of soiled maintenance material and
operating materials at the appropriate collection
point.
Recycle packaging material, metal and plastics.
Anleitung BMH 33-60S_SPK1:_ 13.09.2007 13:59 Uhr Seite 17
Summary of Contents for BMH 33/60S
