EN
- 12 -
in the recess provided for it in the additional
handle.
•
Set the depth stop (2) to the same level as
the drill bit.
•
Pull the depth stop back by the required
drilling depth.
•
Turn the handle on the additional handle (7)
until it is secure.
•
Now drill the hole until the depth stop (2)
touches the workpiece.
5.3 Fitting the drill bit (Fig. 5)
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This impact drill is fitted with a keyless chuck
(1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
6. Operation
6.1 On/O
ff
switch (Fig. 7/Item 5)
In
fi
nitely variable speed control is possible with
the On/O
ff
switch (5). The further you push the
switch, the higher the speed of the cordless
impact drill.
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch o
ff
:
Press the ON/OFF switch (5) brie
fl
y.
6.2 Changeover switch (Fig. 7/Item 6)
Using the changeover switch (6) above the On/
O
ff
switch (5) you can select the direction of
rotation of the cordless impact drill and lock the
cordless impact drill so that it cannot be switched
on accidentally. You can select between clockwise
and counter-clockwise rotation. To avoid causing
damage to the gearing, the direction of rotation
must only be changed when the equipment is at
a standstill. When the slide switch is in the middle
position, the On/O
ff
switch is blocked.
6.3 Drill / impact drill selector switch
(Fig. 8/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / impact drill selector switch (3) in the drill
position. (Position A)
Use for: Wood, metal, plastic
Impact drill
Drill / impact drill selector switch (3) in the impact
drill position. (Position B)
Use for: Concrete, rock, masonry
Tips for working with your impact drill
6.4 Drilling concrete and masonry
•
Switch the Drill/Impact drill selector switch (3)
to position B (Impact drill).
•
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
6.5 Drilling steel
•
Switch the drill / impact drill selector switch
(3) to position A (drill).
•
Always use HSS drill bits (HSS = high speed
steel) and a low speed setting for drilling
steel.
•
We recommend that you lubricate the
hole with a suitable cutting fluid to prevent
unnecessary drill bit wear.
6.6 Starting holes
If you wish to drill a deep hole in a hard material
(such as steel), we recommend that you start the
hole with a smaller drill bit.
6.7 Drilling tiles
•
To start the hole, switch the drill / impact drill
selector switch (3) to position A (drill).
•
Switch the drill / impact drill selector switch
(3) to position B (impact drill) as soon as the
drill bit has passed through the tiles.
6.8 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.9 Battery capacity indicator (Fig. 9 / item 9)
Press the battery capacity indicator switch (10).
The battery capacity indicator (9) shows the
charge status of the battery using 3 LEDs.
Anl_TC_ID_18_Li_SPK7_USA.indb 12
Anl_TC_ID_18_Li_SPK7_USA.indb 12
10.09.2021 09:18:40
10.09.2021 09:18:40
