EN
- 11 -
of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc),
or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.
6. Do not dispose of batteries in
fi
re.
7. Batteries should be recycled or disposed of
as per state and local guidelines.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and
fi
res.
SAFETY INSTRUCTIONS FOR
ANGLE GRINDER
Safety Warnings Common for Grinding or
Abrasive Cutting-O
ff
Operations:
a)
This power tool is intended to function as
a grinder or cut-o
ff
tool. Read all safety
warnings, instructions, illustrations and
speci
fi
cations provided with this power
tool.
Failure to follow all instructions listed
below may result in electric shock,
fi
re and/or
serious injury.
b)
Operations such as sanding,
wire brushing, polishing are not
recommended to be performed with this
power tool.
Operations for which the power
tool was not designed may create a hazard
and cause personal injury.
c)
Do not use accessories which are not
speci
fi
cally designed and recommended
by the tool manufacturer.
Just because
the accessory can be attached to your power
tool, it does not assure safe operation.
d)
The RATED SPEED of the accessories
must be at least equal to the operating
speed setting marked on the power tool.
Accessories running faster than their RATED
SPEED can break and
fl
y apart.
e)
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately controlled.
f)
Threaded mounting of accessories must
match the GRINDER spindle thread. For
accessories mounted by FLANGES, the
arbour hole of the accessory must
fi
t
the locating diameter of the FLANGE.
Accessories that do not match the mounting
hardware of the power tool will run out of
balance, vibrate excessively and may cause
loss of control.
g)
Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and
run the power tool at maximum no-
load speed for one minute.
Damaged
accessories will normally break apart during
this test time.
h)
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments.
The eye protection
must be capable of stopping
fl
ying debris
generated by various operations. The
dust mask or respirator must be capable
of
fi
ltrating particles generated by your
operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i)
Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment.
Fragments of workpiece or of a
broken accessory may
fl
y away and cause
injury beyond immediate area of operation.
j)
Hold the power tool by insulated gripping
surfaces only, when performing an
operation where the cutting tool may
contact hidden wiring.
Contact with a ²live²
wire will also make exposed metal parts of the
power tool ²live² and could give the operator
an electric shock.
l)
Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
l)
Do not run the power tool while carrying
it at your side.
Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
m)
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation
of powdered metal may cause electrical
hazards.
Anl_Axxio_SPK7_USA.indb 11
Anl_Axxio_SPK7_USA.indb 11
08.05.2019 10:08:29
08.05.2019 10:08:29
