GB
- 7 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
General safety information for power tools
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock,
fi
re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
The term „power tool“ used in the safety informati-
on and instructions refers to power tools operated
from the mains power supply (with a power cable)
and to battery operated power tools (without a
power cable).
1. Workplace safety
a) Keep your work area clean and well illu-
minated.
Untidy or unlit work areas can result
in accidents.
b) Do not operate the electric tool in an en-
vironment where there is a risk of explo-
sions and where there are in
fl
ammable
liquids, gases or dust.
Electric tools produ-
ce sparks which could set the dust or vapours
alight.
c) Keep children and other people away
from the power tool while you are using it.
If you are distracted you may lose control of
the power tool.
2. Electrical safety
a) The connector plug from this electric tool
must
fi
t into the socket. The plug should
never be altered in any way. Never use ad-
apter plugs together with earthed electric
tools.
Unaltered plugs and correct sockets
reduce the risk of an electric shock.
b) Avoid bodily contact with earthed sur-
faces such as pipes, heating, ovens and
fridges.
The risk of electric shock is increa-
sed if your body is earthed.
c) Keep the tool out of the rain and away
from moisture.
The ingress of water into an
electric tool increases the risk of an electric
shock.
d) Do not use the power cable for a purpose
for which it is not designed, for example
to carry the power tool, hang it up or to
pull the plug out of the socket. Keep the
power cable away from heat, oil, sharp
edges and moving parts.
Power cables that
are damaged or tangled increase the risk of
an electric shock.
e) If you use an electric power tool out-
doors, use only extension cables that are
suitable for outdoor use.
The use of an
extension cable which is suitable for outdoor
use reduces the risk of an electric shock.
f) If operation of the electric tool in a damp
environment can not be avoided, use a
earth-leakage circuit-breaker.
The earth-
leakage circuit-breaker reduces the risk of an
electric shock.
3. Safety of persons
a) Be careful, watch what you are doing and
use an electric tool sensibly. Do not use
the tool if you are tired or under the in
fl
u-
ence of drugs, alcohol or medication.
A
moment of inattention when using the electric
tool can result in serious injuries.
b) Wear personal protection equipment
and always wear safety goggles.
Wearing
personal protection (such as dust masks,
non-slip safety shoes, safety helmet or ear
protection, depending upon the type and use
of the electric tool) reduces the risk of injury.
c) Make sure that the appliance cannot start
up accidentally. Ensure that the electric
tool is switched o
ff
before you connect
it to the power supply and/or insert the
battery, or pick up or carry the tool.
If your
fi
nger is on the switch whilst carrying the elec-
tric tool or if you connect the appliance to the
mains when it is switched on, this can lead to
accidents.
d) Remove all adjusting tools or wrenches
before you switch on the power tool.
Any
tool or wrench in a rotating part of the power
tool could cause injuries.
e) Avoid abnormal working postures. Make
sure you stand squarely and keep your
Anl_TE_AG_18_100_Li_EX_PH_SPK7.indb 7
Anl_TE_AG_18_100_Li_EX_PH_SPK7.indb 7
28.10.2020 12:58:52
28.10.2020 12:58:52
