GB
10
the operating instructions to be found in this manual.
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about its potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. The following hazards may arise in
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if essential ear-muffs are not
worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.
5. Technical data
Weight
ca. 7 kg
6. Assembling the base frame and
fixing the RT-SM 430 to the base frame
(Figs. 1, 4-14, 15a, 16-18a, 19-21)
1.
Insert the support feet (A) from underneath into
the intermediate struts (C) as shown in Fig. 4.
Ensure that the rubber stoppers on the support
feet (A) are aligned so that their support surfaces
are leveled.
2.
Screw the support feet (A) to the intermediate
struts (C) as shown in Figs. 5-6 using the screws
(N), washers (H) and nuts (G).
3. Slide the side part (B) from the top over the
intermediate struts (C) (Fig. 7).
4. Screw the side part (B) to the intermediate struts
(C) using three screws (L), washers (K) and nuts
(I) at each connection point (Figs. 8-9).
5. Assemble the other part of the base frame as
described above in step 1-4.
6. Take one of the assembled parts (no matter
which one) and insert the two bottom cross struts
(E) as far as possible into the appropriate
openings of the intermediate strut (C)
(Fig. 10). Screw the bottom cross struts (E) to
the intermediate strut (C) using two screws (L),
washers (K) and nuts (I) at each connection
point, as shown in Figs. 11-12.
7. On the same part of the base frame, slide the
two top cross struts (F) as far as possible into the
appropriate openings of the side part (B) (Fig.
13). Insert one corner brace (D) into each
opening of the side part (B). Note that the corner
braces (D) only fit one way on the base frame.
This is the case when the holes in the side part
(B), the top cross struts (F) and the corner
braces (D) line up (Fig. 14).
8. Fasten two of the saw mounts (J) onto the same
part of the base frame as shown in Fig. 15a.
Note that the saw mounts (J) only fit one way on
the base frame. This is the case when the holes
in the side part (B), the top cross struts (F), the
corner braces (D) and the saw mounts (J) are
aligned (Fig.15a).
9. Screw the top cross struts (F), corner braces (D),
side part (B) and saw mounts (J) together, as
shown in Figs. 15a-16 using two screws (L),
washers (K) and nuts (I) each time.
10. Insert the two base frame parts in such a way
that the bottom and top cross struts (E, F) are
positioned in the relevant openings on the side
part (B) and the intermediate strut (C) (Fig. 17).
11. Screw the bottom cross struts (E) to the second
part of the base frame as described in step 6
(Fig. 18a/1.).
12. Screw the top cross struts (F) to the second part
of the base frame as described in step 7 (Fig.
18a/2.).
13. Fasten the other two saw mounts (J) onto the
second part of the base frame as described in
step 8 (Fig. 18a/2.).
14. Pull the four rubber buffers (Z) from the bottom
side of the saw (Fig. 19).
15. Place the saw onto the base frame, align the
holes in which the rubber stops (Z) have been
with the 4 holes on the top side of the saw
mounts (J). Now insert the 4 screws (M) from
above through the saw feet and screw the saw to
the saw mounts (J) (Figs. 20-21).
Anleitung_E_Stand_SPK7:_ 30.06.2011 11:20 Uhr Seite 10
