37
GB
4. Proper use
The lawn mower if designed for use in private
gardens.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Technical data
Mains voltage:
230V ~ 50Hz
Power input:
1700 W
Motor speed:
3,250 min
-1
Cutting width:
43 cm
Cutting height adjustment:
20-70 mm; 6 levels
Volume of catch bag:
52 liters
Sound pressure level
LpA
:
86.9 dB(A)
Uncertainty
KpA
: 2
dB(A)
Sound power level
LWA
96 dB(A)
Vibration at the handlebars a
hv
:
≤ 2.5 m/s
2
Uncertainty K:
1.5 m/s
2
Protection class
II/
쏾
6. Before starting the equipment
The lawn mower is delivered unassembled. The
complete push bar and the grass collector must be
assembled before using the lawn mower. Follow the
operating instructions step-by-step and use the
pictures provided as a visual guide to easily
assemble the machine.
6.1 Fitting the wheels (Figures 3a, b and c)
Take the rear wheels (Figure 1/Item14) and attach
them to the axle as shown on Figure 3a. Then slide
the washer (Figure 2/Item 17) on the axle and fasten
all parts with the supplied split pin (Figure 2/Item 16)
as shown in Figure 3b. Finally, press the wheel caps
(Figure 2/Item 15) onto the wheels (Figure 3c). Fit the
front wheels (Fig. 2/Item 13) in the same way.
6.2 Fitting the push bar (Fig. 4a to 4e)
Fit a bottom push bar (Fig. 4a/Item 2) into the opening
provided for it (Fig. 4a) and secure it as shown in
Figure 4b with a screw (Fig. 4b/Item 19). Proceed in
the same way on the other side.
When you fit the top push bar you can decide the
height of the push bar by selecting the appropriate
fastening hole (Fig. 4c). Fasten the top push bar using
either the holes L for a low position or H for a high
position. Screw the top push bar to the bottom push
bar as shown in Figure
4d. Then attach the power cable to the push bar (Fig.
4e/Item A) using the cable clips (Fig. 2/Item 18).
6.3 Fitting the grass box (Fig. 5a to 5d)
Plug the bottom and the top part of the grass box
together (Fig. 5a/Item 10, 11). Ensure that all the
plastic lugs engage correctly. Next push the grass box
handle (Fig. 5b/Item 12) into the openings on the
grass box. Check that the handle is secure and
correctly positioned.
Before you fit the grass basket you must ensure that
the motor is switched off and the blade is not rotating.
The grass box must be attached to the two hooks on
the mower (Fig. 5c/Item A). To do this, open the
ejector flap with one hand (Fig. 5d/Item 6) and attach
the grass box with the other hand as shown in Figure
5d. The ejector flap is held against the grass box by a
spring.
6.4 Filling level indicator of the grass box
The grass box is equipped with a filling level indicator
(Fig. 2/Item 21) which is opened by the airflow that the
lawn mower generates during operation. If the flap
closes during mowing, the grass box is full and must
be emptied. To ensure the proper functioning of the
filling level indicator, the holes under the flap must
always be kept clean and permeable.
6.5 Setting the cutting heights
Important!
Adjust the cutting height only when the engine is
switched off and the power cable has been
disconnected.
The cutting height is centrally adjusted with the
cutting height adjustor lever (Fig. 6/Item 14). Up to
different cutting heights can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.
Anleitung_BG_EM_1743_HW_SPK7__ 29.01.14 07:48 Seite 37