You have decided in favor of an µ item.
is significantly delayed. This System is firmly
Congratulations on your choice! All µ
anchored in the surface, so no extensive
items are produced of select materials and
flaking will appear. Instead after years the
subjected to severe quality checks.
gloss level will decrease, the colour will fade
and a slight algae cover will appear. This is
All µ items are fabricated in such a way as
not a quality problem, the surface finish can
to allow easy do-it-yourself assembly. We are,
be renewed with a refresh.Depending on the
of course, ready to do that for you. Just let us
place of installation, after several years might
know in advance.To make assembly of your
appear: chalk powdery dust at the surface,
new µ item easy for you, we have
fissures or damage by hail yet without
prepared these assembly instructions. Step by
discolouring of the wood. In this stage a
step you will be guided through the various
refresh should be carried out, to prevent the
assembly stages up to the finished play
Positioning on the Playground:
wood from permanent damages. Sanding the
equipment.Should you encounter any
Please remember that exposure to strong solar
surface in preparation for the refresh is not
unforeseen problems during assembly, please
radiation and thus heating up of the product
necessary. It is sufficient to apply the oil on
get in touch with our service department. Our
should by all means be avoided. This is true
the well-cleaned and dry surface. It is
representatives will be happy to help you.
especially for slide bars and slides. Position the
important that the refresh is carried out before
The occupational health and safety
equipment in natural shadows e.g. of trees or
the following damages appear: clearly visible
regulations at the site of installation must
facing certain directions. We do advise you not
fissures, discolouring of the wood, infection
be observed.
to position the slides towards south-east, south
with wood destructive fungi or insects.
or south-west as the slide surfaces are likely to
Assembly Instructions:
Space Requirements:
heat up very strongly. If you use large-area
Knock round-sheath screws with a rubber
and flexible components such as sun sails or
The first two numbers indicate the minimum
hammer only in order not to damage the
similar shadow-creating elements on your
space required for your µ equipment,
corrosion protection.Use washers under all
playground, make sure to secure them against
including the impact area (formerly safety
nuts and tighten all nuts with "feeling". If you
the effects of wind. Please remove them in case
area). Our floor type recommendations apply
tighten them too strongly, an unnecessary
of strong winds or storms.
to this area.Independently of our
high amount of wood fibers tear off
recommendations, you have to allow for an
Surrounding Area Requirements:
underneath the screw head. Recesses are
obstacle-free area of at least 1.50 m all around
provided for the countersinking of the screw
The area within the safety zone must be even.
the device. This area must be absolutely free of
nuts. For easy positioning of the nuts in the
Please adhere to the indications in our tender
hard or sharp-edged or protruding parts a
recesses, put one or two of them into the
documents and the foundation plan.
child could fall onto. This area is not subject to
wrench and slip onto the screw.
any regulations regarding impact-attenuating
Please make sure that all assembly equipment
Use a two-way drill with enough pull for
flooring.
has been removed before you open the
assembly. A battery-driven screwdriver is
equipment to the children.
Depending on the place of
not suitable!
If the mounting site provides conditions that
installation, after several years
are out of the ordinary, e.g. peaty soil or
Marker Holes:
might appear: chalk powdery dust
frozen ground, such conditions absolutely
The column bases bear bore holes indicating
at the surface, fissures or damage
have to be taken into account.
up to what height they have to be planted
by hail yet without discolouring of
All changes on parts of the equipment or on
and covered with the bulk material (e.g. sand,
its construction which may affect the basic
the wood. In this stage a refresh
tree bark mulch). You should plant the column
safety of the device are subject to prior
bases in such a way as to allow the marker
should be carried out, to prevent
manufacturer approval.
holes to remain clearly visible from the outside
the wood from permanent
of your µ product.
Have fun with your play equipment!
damages. Sanding the surface in
µ Prod Vertrieb GmbH & Co. KG
Materials Used:
preparation for the refresh is not
Industriestr. 1
wood is a natural product. Temperature
necessary. It is sufficient to apply
D-97285 Röttingen
fluctuations may therefore cause minor cracks
the oil on the well-cleaned and dry
and deformations which do, however, neither
Germany
surface. It is important that the
affect the load carrying capacity of the wood
Tel. +49-(0)93 38/89-0
nor represent a reason for complaints. Being a
refresh is carried out before the
Fax +49-(0)93 38/89-199
recognized impregnation company, µ is
following damages appear: clearly
authorized to carry the RAL quality mark and
E-Mail [email protected]
visible fissures, discolouring of the
is therefore subject to regular third-party
www.eibe.net
inspections. You can therefore rely on all
wood, infection with wood
batches being impregnated correctly. µ
destructive fungi or insects.
uses core-separated wood as it is less prone to
cracks than boxed heart (wood with core).
Please adhere to the occupational
health and safety regulation that
Wood protection:
apply to the installation site
you need not refresh the wood protection
carried out by means of the µ
Disposal:
impregnation. Due to climatic influences / UV
• Impregnated waste wood: thermal disposal
radiation, the outer cell structure slowly
• Metals, noble metal, GRP, plastics: textile
decomposes, constituents such as tannic acid
disposal
are extracted, the wood is being leached and
takes on a gray color. This is a purely external
Labeling:
effect and does not constitute any
all µ products are marked with a label or
deterioration of quality, stability or wood
sticker. Label or sticker inform on delivery date
protection. If you are bothered by the fading
•(1), the feedback number (2)‚ (in few cases the
colors, you can freshen up the wood by way of
product article number), and the valid
a transparent, water-based shade equalizer
standard (3). Please indicate both delivery
which needs not contain fungicides or
date and feedback number in all complaints
biocides. Varnished components, however,
and repeat orders.
need to be repainted after two years, then
every year.
eibe resistant playground timber (rpt) is
treated with a protective oil based surface
finish. Due to enclosed pigments and special
ingredients the natural process of weathering
<P>
1
2
3
552024143..
3 / 10
