L
N
230 V~
1308.1
230
V~
9
90
2
4
PIN
1
IN
1
OUT
5
IN
6
IN
7
IN
8
IN
5
OUT
6
OUT
7
OUT
8
OUT
+
R L
N L
R L
+RR+L L
L+ L R+ R
R
IN
L
IN
4
PIN
115/230 V~
115/230 V~; +-15%; 50/60 Hz
009105 04/2018
Hotels
1 2 1 0 . 1 0 H
First connection
1.
Press key to turn on the sound unit for the first time.
Bluetooth
®
mode will be selected and the
blue led
will start to blink quickly.
That means its ready to be paired with other device.
If the paired device list is empty, the sound unit will blink quickly.
If the sound unit has a previous link with other device (i.e. Paired Device List is not empty), it will blink slowly.
Audio source selection and volume level are stored when the device is turned off. In case of power failure, it will
return to Bluetooth mode when turned on.
NOTE:
When the sound unit is at bluetooth
®
mode and visible/pairable, it´s displayed to other devices as
"
EGi 1210.10H xxxx
". Paired device list is empty when the sound unit comes from factory. The unit can store
up to 8 paired devices.
A short press on
, key will make the sound unit visible/pairable, so that a new device can be paired with it.
When the Paired Device List is full, the oldest connection device (i.e. the least used) will be erased from it, and
replaced for the new one (see paragraph
2.
).
2.
If key
is pressed, the blue LED will blink quickly. It shows that the sound unit is visible for other bluetooth
®
devices,
and therefore can be paired with any bluetooth
®
audio source..
Once paired with a new device, the audio unit stores its data in the paired device list. Then the blue led will light continuously
and the unit will be playing audio indefinitely until it is turned off, another audio source is selected, the user disconnects it
manually, or maximum distance between the unit and the device is exceeded.
3.
When key is pressed, the sound unit will go to bluetooth
®
mode, regardless of its previous state.
Blue LED will blink slowly and the unit will try and reconnect to the last connected Bluetooth device.
If it fails, itll try to reconnect with the following device from the paired device list, and so on until it reaches the end of the list.
Press twice the ON/OFF key to force a new search .
If the device is disconnected by the user or by exceeding the maximum distance, the blue led will start to blink slowly.
That means that the unit can be connected to any device of the paired device list.
NOTE:
To clear paired device list, please hold the key
pressed for 6 seconds.
Normally it is not necessary, because every time a new device is paired, the unit erases the least used device from the list
to store the new one.
EGi
guarantees its electronic and electroacoustic products against any manufacturing defect that affects its operation for
36 months from the production date
(indicated in every
manufacture), taking the commitment of repairing or replacing the faulty modules which failure, always to the discretion of
EGi
, is caused by a manufacturing defect, without any charge for
spare parts.
This guarantee does not include charges for the shipping and handling of the modules, nor the labour charges for the replacement in the installation of the aforementioned electronic and electroacoustic
modules. The guarantee will not cover in any case the damages or breakings of the trimming pieces (lattices, trims, masks, frames...).
This guarantee refers
only
to the concept of
replacement in factory of the modules
produced by
EGi
, excluding any other cover or responsibility on the rest of the materials or the
whole of the installation that is put at the user disposal, but that is not supplied nor executed by
EGi
.
Therefore this guarantee does not cover:
a.
The fitting up and the interconnection between the modules.
b.
The results from the abuse or misuse of the product, including but not limited to:
b.1. Not using the product for usual purposes, or not following the instructions from
EGi
for the correct use and maintenance of the product.
b.2. The installation or use of the products in a way that is not concordant with the technical or security rules now in force.
c.
The malfunctions caused by the wrong installation of the modules, or by an installation with inappropiate cables.
d.
The malfunctions caused by the intervention of a person non-authorised by
EGi
.
e.
The consequences of mixing with equipment from other sources, and also adaptations, modifications, adjustments and/or adjustment attempts, irrespectively of those that have been
performed in a technically correct way, provided that there is not an express authorisation by
EGi
.
f.
The consequences of accidents, natural catastrophes or any cause beyond
EGi
control, including but not limited to lightning, water and public disturbances.
In all these cases that are excluded from the guarantee, and every time that the modules are not considered as faulty by
EGi
, the sender should take responsibility of the full amount of
the repair, and in the event of a visit from our technicians, the requesting person will bear the expenses originated without a cause justified in the guarantee.
ATTENTION:
If you notice any problem in your
EGi
installation, our Customer Support Service will attend you from 9h. to 13h (Central European Time).
Guarantee
Technical specifications
1210.10H
Bluetooth
®
control unit with AUX/TV and PIN
e n
i n s t r u c t i o n m a n u a l
Av. Almozara, 79 50003 ZARAGOZA - Spain
T.
+34 976 40 53 56
F.
+34 976 40 53 54
e-mail:
[email protected] www.egiaudio.com
Wiring diagram
Function
Display
Multicolor led
Main power input
115/230 V~; 50/60 Hz
Consumption (max)
7 W
Consumption stand-by
0.2 W
Sensitivity inputs AUX and TV
500 mV
RMS
Sensitivity input PIN
3 V~
RMS
+ 7 V
Input impedance
10 K
W
Loudspeaker impedance (min)
16+16
W
Max. power
2+2 W
RMS
audio
Housing
ø60 mm box
Dimensions (mm)
45 x 45 x 52
Finish
White
NOTE:
This example shows the stage 40425 connection but also can be connected with
models 40426, 03001, E17G/D and 40430. If you choose the power stage
E17G/D
, it is necessary to use the "
45
" as negative or ground connection.
Impedance
16
W
Impedance
16
W
Audio coaxial cable.
Analog TV audio output from jack to
headphones or SCART connector.
Impedance
4
W
PIN
input from audio calls channel "
1
"
or MILLENNIUM audio output "
OUT +
".
The configuration with power stages
can be made with speakers in parallel
or without speakers at the output of
the sound unit 1210.10H.
Impedance
4
W
L
- Left
R
- Right
L
- Left
R
- Right
4.
Volume is controlled by
+
and
keys. It has 32 steps of 2dB each one.
Volume is set from factory to a medium level.
The unit memorizes the volume level selected by the user, so that it is restored when the unit is turned on.
However, after a power failure, the volume level is restored to its factory setting.
NOTE:
Remember that bluetooth
®
devices have an independent volume control. Therefore, we recommend adjusting unit
volume near to its maximum and using device volume control. This way, maximum performance is achieved while the user
has a more comfortable volume control.
5.
By pressing
TV > AUX
key, the unit switches from bluetooth
®
to TV mode. Audio from rear connection is selected and
led
changes to
green
.
Then, if
TV > AUX
key is pressed again, the unit will switch to
AUX
mode. Audio from front 3.5mm jack will be selected
and
led
will change to
yellow
.
If
TV > AUX
key is pressed again,
TV
mode will be selected and so on.
6.
Priority audio input (
PIN
) is activated
ONLY
by a Millennium signal. It consists of a +3 V~ audio level superimposed to a
+7 V level (referred to
GND
).
Regardless of the control unit state (ON, OFF, bluetooth
®
, TV or AUX), if
PIN
input is activated, audio from this input will
be selected,
led
will switch to
red
and volume control will go to maximum level. This unit will remain at this state until
PIN
input is deactivated, returning to its previous state.
We recommend the use of MILLENNIUM equipment (1308.1, 1310.1 or 1304.1A) to utilize this function.
The sound unit must be connected to a mains voltage between 115 and 230 V~ 50 / 60Hz, prior to being used.
The sound unit remains at OFF/Standby state when powered for the first time or after a power failure (even if it was ON before).
Even with the sound unit in ON position, if it suffers a blackout of power grid, at the return of the mains supply the sound unit mode, always stays on OFF or stand-by
position.
To obtain the best sound quality, check speaker connections before turning on the device (no short-circuits, correct polarity and minimum impedance).
Troubleshooting
Problem
The sound unit doesnt turn on.
The sound unit turns on, but theres no sound.
The blue led blinks slowly, but the unit doesnt connect with a paired
device.
The unit is at TV or AUX mode, and theres no sound.
Possible solution
Check if the sound unit is powered. A voltage between 115 and 230 V~ 50/60Hz
must be applied to
L
and
N
terminals.
Check that the speakers are properly connected to
L+
/
L
and
R+
/
R
outputs. Verify the absence of short-circuits and check that line impedance
is above 11 ohms. Make sure that a bluetooth
®
device is connected, or a
signal is present at TV or AUX inputs. Set volume level to maximum.
Check that your device has Bluetooth connectivity enabled. Press twice the
ON/OFF key to force a new search through the paired device list . To force
a pairing process, press
key.
Verify that an analog signal with a level around 250-500 mV is present at TV
(rear terminals) or AUX (front 3.5 mm jack) inputs.
ABOUT THIS MANUAL
We have taken all efforts to make the contents of this manual reliable and updated.
However,
EGi
does not guarantee the accuracy of the contents which are subject to
change without previous notice.
TECHNICAL SUPPORT
If, while using the system, you encounter a problem that cannot be solved by consulting
the manual, please contact the installer. You can also consult the website
www.egiaudio.com
to find the latest information and other resources to solve your
problem.
COPYRIGHT INFORMATION
This manual in whole or in part, and any product or software described herein, may
not be reproduced, transmitted, saved in data recovery systems, or translated into
any language in any form or by any means, except all documents saved by the user
to make security copies; without the previous written consent of the manufacturer.
All products or corporate names herein may (or not) be registered trademarks or
copyright of their respective companies and are used for identification or explanatory
reasons only, and in interest of the owner without the intention of infringing any
regulation or rule.
SAFETY INSTRUCTIONS
This system has been designed and manufactured in compliance with the latest safety
standards for household electronic equipment. However, to ensure safe use of this
product, it is important to follow the instructions given in this documentation:
No
EGi
product should be covered with anything that impedes ventilation.
Do not place any sources of naked flame such as lighted candles or similar elements
on top of the device.
Do not expose the device to poured, splashed or sprayed water.
Disconnect the Mains supply before carrying out any work on the installation.
Do not expose the equipment to direct sunlight.
Do not use excessive force when handling the controls.
The user should abstain from carrying out any alterations or repairs on the product,
reserving these actions for qualified personnel.
Only use accessories supplied by
EGi
.
EGi
will not be held liable for any damage arising from misuse of the product or usage
other than what is was designed for (See
Guarantee
section).
An exclamation mark inside a triangle indicates important operation
and maintenance instructions and the existence of components that
may affect safety if replaced.
Class II device.
IMPORTANT
Please read these
"Safety instructions"
carefully before using any
EGi
product.
The lightening-shaped arrow warns of the presence of dangerous voltage.
To minimise the risk of electric shock, do not remove the cover.
The lightening signs near the amplifier output terminals warn of the danger
of electric shock in normal usage conditions (Terminals dangerous to touch).
Do not touch these terminals while the device is in operation.
This symbol indicates that the product must not be treated as normal domestic
waste, but must be handed over to the corresponding collection point for
electrical and electronic equipment.
The smark means European Conformity and is a European mark for
certain groups of services or industrial products.
The mark must be displayed by a product if it is within the scope of the
approximately 20 "New Approach" Directives and can be sold and put into
service legally within the countries of the EU. If the product complies with
the provisions of applicable European Directives and the is displayed
on the product, member states cannot prohibit, restrict or impede the
placement of the product or service on the market. Thus, the mark can
be considered as a passport for commercialising a product in EU countries.
LIABILITY
Due to the wide variety of services and devices the system interacts with, the manufacturer
cannot be held liable for failure or faulty operation of devices not manufactured by
EGi
and
connected or used by any module in the series.
DECLARATION OF CONFORMITY
Electroacústica General Ibérica, S. A. with registered address in Avda. Almozara, 79 - 50003
Zaragoza (Spain), declares under its sole responsibility that the equipment described in this
manual incorporates the functions specifies in each case and complies with current regulations:
Directive 2004 / 108 EC, regarding electromagnetic compatibility and Low Voltage Directive
2006 / 95 / EC, regarding safety in low voltage receivers.
Due to a policy of continuous improvement,
EGi
reserve the right to modify their
products at any time. Although every effort is made to present up to date documentation,
the documents and illustrations provided may not coincide with the product purchased.
You can access the latest versions of documentation in:
www.egiaudio.com
EGi
will not be held liable for any possible errors in the text or references.
All brands mentioned herein are registered with their owners.
información
Information
For use in Mexico, the operation of this equipment is subject to the following two conditions:
1.
It is possible that this equipment or device does not cause harmful interference and
2.
This equipment or device must accept any interference, including interference that
may cause undesired operation.
