Edwards nXDS10i nXDS15i Instruction Manual Download

Page: 14 / 58

supplied through a suitable external valve and by using the appropriate adaptor,

available as an accessory. Refer to

Spares and accessories on page 48

Figure 2 Quick start guide (manual control mode)

OPERATION

SELECT

STATUS

SECTION

Apply power

MAINS

POWER

The pump will remain off (factory

default).

The POWER INDICATOR will

illuminate.

Electrical supply

connection on

page 29

Start the pump START

BUTTON

The pump will accelerate up to full

running speed.*

The RUN INDICATOR will flash while

accelerating.
The RUN INDICATOR will remain on

when the pump reaches full speed.

Start and stop on

page 32

Stop the pump STOP BUTTON

The pump will decelerate and stop

running.
The RUN INDICATOR will flash while

decelerating.
The RUN INDICATOR will go off when

the pump has stopped.

Start and stop on

page 32

Select and

deselect the

standby speed

STANDBY

MODE SELECT

BUTTON

When engaged, the STANDBY

INDICATOR will illuminate and the

pump will run at the standby speed

setting. Factory default is 70% of full

speed.

Standby on page

Page 12

A73501880_G - Introduction

Summary of Contents for nXDS10i nXDS15i



























































Search results

Summary of Contents for nXDS10i nXDS15i

Reviews:

Related manuals for nXDS10i nXDS15i

Brands by name

Popular brands

Edwards nXDS10i nXDS15i, Instruction Manual

Search results

Summary of Contents for nXDS10i nXDS15i

Reviews:

Related manuals for nXDS10i nXDS15i

Brands by name

Popular brands