Edwards CXS Instruction Manual Download Page 39 | Manualshive

Page: 39 / 40

background image

© Edwards Limited 2016. All rights reserved.

Page 31

Edwards and the Edwards logo are trademarks of Edwards Limited.

Storage and disposal

D397-53-880 Issue C

6

Storage and disposal

6.1

Storage

Store the Profibus Module in clean dry conditions until required. When required for use, install the Profibus Module
as described in

.

6.2

Disposal

Dispose of the Profibus Module and any components safely in accordance with all local and national safety and
environmental requirements.

Alternatively, you may be able to recycle the Profibus Module and/or cables; contact Edwards or your supplier for
advice (also see below).

The Profibus Module and associated cables are within the scope of the European Directive on Waste Electrical and
Electronic Equipment, 2002/96/EC. Edwards offer European customers a recycling service for the Profibus Module/
cables at the end of the product’s life. Edwards' Registration Number as a UK producer of electrical and electronic
products is WEE/BF0054TQ. Contact Edwards for advice on how to return the Profibus Module/cables for recycling.

«
...
37
38
39
40
»

Summary of Contents for CXS









































Reviews:

No comments

Related manuals for CXS

Brand: UE Pages: 4

Brand: Eaton Pages: 6

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: National Instruments Pages: 29

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: Laars Pages: 28

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands