All Rights Reserved.
1
P/N 3102233 – Rev. A – Oct 16, 2014
562NSTT-OEM-ATT01
Smoke Alarm with Heat Detection Sensor
Product Introduction
This wireless photoelectric smoke alarm and heat detector (product)
continually monitors operational status and provides a visual trouble
condition if it drifts out of the sensitivity range or fail internal diagnostics.
This product meets National Fire Protection Association (NFPA) 72 field
sensitivity testing requirements without the need for external meters.
The alarm sensitivity level can be determined at the product. Another
feature is built-in drift compensation that allows the product to adjust
sensitivity automatically as it becomes dirty over time. The drift
compensation feature dramatically increases the time between
cleanings, and reduces the chance of a nuisance alarm. Additional
diagnostic information is activated by applying a magnet near the
detector’s integral reed switch. This initiates a self-diagnostic routine
and provides visual indication of sensitivity level, or if service is
required. The product is powered by long-life 3V Lithium batteries
providing power to both the sensor and wireless transmitter.
This wireless product works in conjunction with your wireless Control
Panel, providing a local indication.
About This Guide
This User Guide describes how to install, operate, and maintain this
product. The User Guide is organized as you are intended to use this
product, following the step-by-step instructions.
Keep this document in a handy location and refer to it when you have
questions about this product and its functions and features. Reading
this guide is the only way to learn how to use your product wisely and
to know how to react in the event of an alarm.
1.
General Information
Congratulations on purchasing your Smoke Alarm with Heat Detection.
The product is designed to be used with a Control Panel as part of the
Fire and Life Safety signaling device. This product has an optical sensor
capable of detecting smoke particles in the event of fire. It also contains
an integrated heat sensor that is triggered if a room experiences a
sharp rise in temperature in the event of fire.
Parts List
One Smoke Alarm
Two CR123A lithium batteries
Mounting Plate
Mounting Screws and Anchors
User Guide
NFPA Guidelines
NFPA 72, 17.5.3.1 Total (Complete) Coverage
Where required, total coverage shall include all rooms, halls, storage
areas, basements, attics, lofts, spaces above suspended ceilings, and
other subdivisions and accessible spaces, as well as the inside of all
closets, elevator shafts, enclosed stairways, dumbwaiter shafts, and
chutes.
NFPA 72, 17.5.3.2 Partial or Selective Coverage
Where codes, standards, laws, or authorities having jurisdiction require
the protection of selected areas only, the specified areas shall be
protected in accordance with this Code.
NFPA 72, 17.5.3.3 Non-required Coverage
Where installed, detection that is not required by an applicable law,
code, or standard, whether total (complete), partial, or selective
coverage, shall meet all of the requirements of this Code, with the
exception of the prescriptive spacing criteria of Chapter 17.
NFPA 72, 17.6 Heat-Sensing Fire Alarms
Heat-sensing fire alarms shall be installed in all areas where required
by the NFPA codes and standards or by the authority having
jurisdiction.
NFPA 72, 29.5.1.1 Required Detection for Single- and Multiple-
Station Smoke Alarms
Approved, single-station smoke alarms shall be installed as follows:
(1)
In all sleeping rooms (applies to several occupancies
including: one- and two-family dwellings; lodging or rooming
houses; hotels, motels, and dormitories; apartment buildings;
residential board and care facilities; and day-care homes)
and guest rooms (applies in the context of hotel and
dormitory occupancies)
(2)
Outside of each separate dwelling unit (applies to one- and
two-family dwellings and dwelling units of apartment
buildings, including condominiums) sleeping area, within 21 ft
(6.4 m) of any door to a sleeping room, with the distance
measured along a path of travel
(3)
On every level of a dwelling unit, including basements
(4)
On every level of a residential board and care occupancy
(small facility), including basements and excluding crawl
spaces and unfinished attics
(5)
In the living area(s) of a guest suite (an accommodation with
two or more contiguous rooms comprising a compartment,
with or without doors between such rooms, that provides
living, sleeping, sanitary, and storage facilities)
(6)
In the living area(s) (any normally occupiable space in a
residential occupancy, other than sleeping rooms or rooms
that are intended for combination sleeping/living, bathrooms,
toilet compartments, kitchens, closets, halls, storage or utility
spaces, and similar areas) of a residential board and care
occupancy (small facility)
2.
Mounting Guideline
This product is a member of a reliable, high-quality product family
using the latest technology available. Review the information in this
section to ensure you get the most out of the product. The information
in this User Guide is in accordance with NFPA 72.
Pre-installation Considerations
Install the smoke alarm in accordance with NFPA Standard 72,
Chapters 17 and 29. Depending on the application, you may need to
reference other chapters of NFPA 72 or NFPA 101.
Choosing an Installation Location
When choosing an installation location, consider:
o
Use of structure and type of construction
o
Contents you want to protect and their burning characteristics
o
Human occupancy
o
Total area to be monitored
o
Ceiling height and surface condition
o
Air movement and vent locations
o
Obstructions
o
Deflections
