manualshive.com logo in svg

EdgeStar IB450BL, Owner'S Manual, Page: 19 / 21

Share
Download
EdgeStar IB450BL Owner'S Manual Download Page 19

15 

 

 

 
 

Issue 

Possible Cause 

Solution 

The machine won't 
operate.  

The icemaker is unplugged. 

Plug the icemaker in. 

The breaker is tripped. 

Reset the breaker. 

The icemaker power switch 
is OFF. 

Switch the icemaker power switch to 
ICE (ON). 

The ice storage bin is full of 
ice. 

Take away some ice cubes and make 
sure the ice-full probe is free of ice. 

The water doesn't feed in 
after the icemaker starts. 

The water supply tap is 
turned off. 

Turn on the water supply tap. 

The water supply pipe is not 
properly connected. 

Reconnect the water supply pipe. 

The machine makes ice, 
but the bin does not fill up 
with ice. 

The condenser may be dirty.  Clean the condenser. 
The air flow to the ice maker 
may be obstructed. 

Check the installation. See the 
“Installation” section. 

The ambient temperature 
and water temperature are 
high, or the unit is close to a 
heat source.  

Check the installation.  See 
“Installation” section of this manual. 

Water is leaking out of the 
unit. 

A few water droplets are on 
the door. 

Under some conditions, humidity may 
condense on the door. Consider 
moving the unit or just be more 
careful when you open the door. 

The water supply connection 
is leaking. 

Tighten the fitting. See the 
“Connecting the Water Line” section. 

The unit is not level. 

Level the feet.  See 

the “Leveling the 

Ice Maker” section. 

The ice cubes are partially 
formed or are white at the 
bottom.  

There is not enough water in 
the water bin. 

Check if the water supply pressure is 
below 15 PSI. 
Check the water supply. The filter 
may be restricted. 
Check for a water leak in the water 
trough. 

There is noise during 
operation 

The unit is not level. 

Level the feet. See 

the “Leveling the 

Ice Maker

” section. 

Certain sounds are normal. 

See 

the “Normal Sounds” section. 

The icemaker stops 
suddenly while making ice. 

The electricity is off. 

Reconnect the power supply line. 

The room temperature is out 
of the stated range. 

Make sure unit is installed with correct 
clearances and within the stated 
ambient temperature range. See 
“Installation” section of this manual. 

The body of the ice maker 
is electrified. 

The ground line isn't in the 
socket.  

Use the correct plug and outlet. 

Scale Builds up quickly 
inside the machine. 

The calcium level in the 
water is too high. 

Use a water filter installed in front of 
the water inlet valve. 

Summary of Contents for IB450BL






















Reviews:

No comments