EdgeStar IB250BL Owner'S Manual Download Page 10

 

 

Important: Once you are ready to install the ice maker in a cabinet or directly on the floor, 
you must adjust the feet to level the ice maker. If the floor is level, just rotate the two front 
feet to touch the floor. 
 

 
Important

:

 Before you begin, unplug the ice maker or disconnect the power. 

Leveling the Ice Maker 

 
 
 
 
 

 
It is important for the ice maker to be leveled in order to work properly. It 
can be raised or lowered by rotating the four rubber feet on the bottom of 
the machine. If you find that the surface is not level, rotate the feet until the 
ice maker becomes level. You may need to make several adjustments to 
level it. We recommend using a carp

enter’s level to check the machine. 

1. 

Place a carpenter’s level on top of the product to check if the ice 
maker is level from front to back and side to side. 

2.  Adjust the height of the feet as follows: 

 

Turn the leveling feet to the right to lower that side of the ice maker. 
Turn the leveling feet to the left to raise that side of the ice maker.  

Reversing the Door Swing 

Tools needed: flathead screwdriver, Phillips screwdriver 
 
 
 

 

1.  Using a flathead screwdriver, separate the hinge axis from top hinge. 
2.  Remove the three screws securing the top hinge to the cabinet. Remove the plug 

buttons opposite the top hinge. Place hinge, screws, plug buttons and hinge axis 
safely aside.  

3.  Open the door about 20 degrees, then lift the door off the bottom hinge 2 and set the 

door aside. 

4.  Remove the three screws securing the bottom hinge to the cabinet and the plugs 

opposite. 

5.  Rotate the door 180 degrees from its original position. The handle should be opposite 

the door hinges. 

6.  Replace the original top hinge on the opposite side at the bottom and the original 

bottom hinge on the opposite side at the top. 

7.  Install the hinge axis back through the bottom hinge. Gently place the door on the 

bottom hinge and open it approximately 20 degrees. 

8.  Install the top hinge axis and tighten firmly. Replace all plug buttons. 

 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for IB250BL



















Reviews: