Edge ED71200 User Manual Download Page 8

1. Low Level Input

For connection to any source (head unit)  with a low level output. This is your RCA output from 

the source (headunit).

2. Gain Control

Used to match the input signal of the source to the amplifier. See the setup section for more 

details.

3. Low Pass Filter Control

Low pass frequency control. The frequency ranges from 40 Hz to 250 Hz.

4. Phase Control

Can be used to alter the phase of the subwoofer from 0 - 180 degrees.

IE: the speaker output can be Inphase or out of phase with the other speakers in the vehicle. 

For best results flick between the two settings to determine the best results. 

5. Subsonic Filter Control

This is used to filter out unwanted amplifier output to the subwoofer. Effectively this will filter 

out all the frequencies up to the crossover point set with the control. The range is from 15 Hz to 

50 Hz.Frequencies of 80 Hz and below cause the subwoofer to work hard, some subwoofers 

cane easily be damaged when playing very low frequencies. Using the subsonic filter allows 

less distortion, delivers frequencies better suited to the subwoofer prolonging its life.

6. Subsonic Filter Switch

Used to turn the filter on or off.

7. Bass Boost control  

To provide up to an extra +18 dB of bass boost at 45 Hz. Use this boost to increase bass 

output from the amplifier.

8. Bass Remote Input Jack

Use to plug in the remote bass controller. 

 

9. Indicator LED

When the amplifier is operating correctly the LED will show as green. When the amplifier is in 

protection mode the LED will show as red.

10. Fuses

Please ensure the following fuse rating is used when replacing fuses:

35 amp x 4

11. Speaker Terminal Output

For connection to the speakers. See Application section for wiring examples.

12. Power Connections

Power connections. See Connections section for details on correct connections.

13. Low Level Output

Daisy chain RCA connection to allow easy addition of another amplifier.

P o w e r 

P r o t e c t 

S P - 

S P - 

S P + 

S P + 

I n p u t 

L + 

R + 

L - 

R - 

H i  L e v e l 

L i n e O u t 

L i n e I n 

O F F 

O N 

S u b s o n i c 

P h a s e 

L P F 

G a i n 

M i n  M a x  3 5 H z  2 5 0 H z  0 °  1 8 0 ° 

8 0 H z 

1 6 H z 

2 4 d B 

0 d B 

R e m o t e 

B a s s 

B o o s t 

ED72500

ED71200 

ED71200 

ED7800

ED7800

ED72500

MONOBLOCK AMPLIFIER  1 X 1250 WATTS RMS

ED71600

ED71600 

4 CHANNEL AMPLIFIER  4 X 200 WATTS RMS

ED7400 

ED7400 

2 CHANNEL AMPLIFIER  2 X 100 WATTS RMS 

MONOBLOCK AMPLIFIER  1 X 600 WATTS RMS 

4 CHANNEL AMPLIFIER  4 X 100 WATTS RMS

4 x 35 AMP

3 x 35 AMP

INPUT  

2 x 15 AMP 

2 x 25 AMP

2 x 20 AMP

1

2

5

7

8

3

4

6

9

10

11

12

13   

1

2

3

5

7

8

6

4

9

10

11

12

1

2

3

4

9

5

6

7

14

8    

10    

11

12

13

1

1

2

3

4

5

6

8

9

10

11

12

13

7

2

3

4

5

6

7

8

9

10

11

12

13

14

Terminals and Controls ED72500

Summary of Contents for ED71200













Reviews: